Lincoln Electric IM510 RANGER 8 - Manual (Page 23)

C-1 ACCESSORIES C-1
RANGER 8
OPTIONAL EQUIPMENT
(Field Installed)
K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR
SMALL WELDERS - For road, off-road and in-plant
and yard towing. (For highway use, consult applicable
federal, state and local laws regarding requirements
for brakes, lights, fenders, etc.). Order:
K957-1 Trailer
K958-1 Ball Hitch
K958-2 Lunette Eye Hitch
K959-2 Fender & Light Kit
K965-1 Cable Storage Rack
K889-2 & -3 Two-Wheel Undercarriage - For moving
by hand. Overall Width 29 in (.74m) Both have pneu-
matic tires. Puncture proof tires included with K889-3.
K1631-1 Puncture Proof Wheel Kit - For converting
K889-2 to puncture proof pneumatic tires.
K893-1 Caster for Undercarriage - Mounts to the
front of the K889-2 to allow easy movement on
smooth surfaces. Includes 6” diameter hard rubber
wheel and convenient toe-on, toe-off locking brake.
K933-1 Four Wheel Undercarriage - For Hand
Moving. Rear pneumatic tires, front molded wheels.
K934-1 Cylinder Brackets - For use with K933-1. for
transporting either one LPG fuel cylinder or one weld-
ing gas cylinder.
K1737-1 FOUR WHEEL ALL-TERRAIN UNDER-
CARRIAGE - For moving by hand at construction
sites. Heavy duty puncture resistant pneumatic tires.
K1770-1 UNDERCARRIAGE (FACTORY) - For mov-
ing by hand on a smooth surface. One or two gas
cylinders can be mounted on the rear of the undercar-
riage with the installation of K1745-1 Cylinder
Holder(s). Heavy duty puncture resistant pneumatic
tires and front caster.
K1745-1 SINGLE GAS CYLINDER HOLDER
For use on K1770-1 Undercarriage. One or two may
be installed on an undercarriage.
K1788-1 ROLL CAGE - Gives added damage protection.
K886-1 Canvas Cover -To protect the Ranger 8 when
not in use. Made from attractive red canvas material
which is flame retardant, mildew resistant, and water
repellent.
K802-R Power Plug Kit - Provides four 115V plugs rated at
15 amps each and one dual voltage, full KVA plug rated at
115/230V, 50 amps.
K802-N Power Plug Kit - Provides four 115V plugs
rated at 20 amps each and one dual voltage, full KVA
plug rated at 115/230V, 50 amps. (For K1418-2 or
K1419-2 CSA machines and machines with GFCI
receptacles, use K802-R).
K704 Accessory Kit - Includes 35 ft (10.7m) 2/0 AWG elec-
trode cable, 30 ft. (9.1m) 2/0 AWG work cable, headshield
with No. 12 filter, GC300 work clamp and Cooltong® 300
electrode holder. Cables are rated at 300 amps, 100% duty
cycle.
K892-1 Remote Control Receptacle Kit - Includes a 6-pin
MS-type (Amphenol) receptacle and a local-remote toggle
switch that mounts in the case front. Required when using a
K930-2 Tig Module with an optional Amptrol or when using a
Remote Control.
K857 25 ft (7.5m) or K857-1 100 ft. (30.4m) REMOTE CON-
TROL - Portable control provides same dial range as the
output control on the welder. Has a convenient 6 pin plug for
easy connection to the welder.
K894-1 Spark Arrester Kit - Includes a heavy gauge steel,
approved spark arrester and clamp for easy mounting to
muffler exhaust pipe.
K896-1 GFCI Receptacle Kit - Includes two UL approved
115V ground fault circuit interrupter duplex type receptacles
with covers and installation instructions. Replaces the two
factory installed 115V duplex receptacles. Each receptacle
of each GFCI duplex is rated at 15 amps, but the maximum
total current from each GFCI duplex is limited to 20 amps.
K930-2 TIG Module - Provides high frequency and shield-
ing gas control for AC and DC GTAW (TIG) welding applica-
tions. Its compact case is designed for easy carrying, com-
plete with a handle. High frequency bypass is built in. The
K938-1 Contactor Kit must be field installed in the TIG
Module when used with a Ranger 8. Additionally, the K936-
3 control cable is required if remote control is used. If
remote control is not used the K936-4 control cable is
required.
K936-3 Remote Control Cable - Control cable for connect-
ing the K930-2 TIG Module to a Ranger 8 equipped with a
K892-1 Remote Kit. 9-Socket to a grounded 115 V plug and
a 6 pin MS-connector. (Contains circuits 2, 4, 31, 32, 75, 76,
77 and ground)
K939-1 Docking Kit - For mounting the K930-2 TIG Module
unit on top of the Ranger 8.
K1816-1 FULL KVA ADAPTER KIT - Plugs into the
120/240V NEMA 14-50R receptacle on the casefront (which
accepts 4-prong plugs) and converts it to a NEMA 6-50R
receptacle, (which accepts 3-prong plugs.)