Lincoln Electric IM511 RANGER 9 - Manual (Page 34)

– 32 –
1 2 - 1 6 - 9 3
M 1 7 0 9 2
ELECTRODE CABLE
OPTIONAL K857
REMOTE CONTROL
TO WORK ELECTRODE
6 PIN
AMPHENOL
14 PIN
AMPHENOL
TO WORK
TO WIRE FEED UNIT
TO LN-7 INPUT
CABLE PLUG
CAUTION :
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
N.B. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE
APPLICATIONS. SEE OPERATING MANUAL.
N.A. USE POLARITY SWITCH TO SET FOR DESIRED ELECTRODE POLARITY. POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
N.C. IF OPTIONAL REMOTE OUTPUT CONTROL IS USED, PLACE OUTPUT CONTROL SWITCH IN "OUTPUT CONTROL REMOTE" POSITIION.
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
RANGER 9 / LN-7 CONNECTION DIAGRAM
PLACE WELDING TERMINALS SWITCH TO "REMOTELY CONTROLLED" POSITION.
N.D. PLACE IDLER SWITCH IN "HIGH" IDLE POSITION.
K584-XX INPUT CABLE ASSEMBLY
WARNING
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.
1 2 - 1 6 - 9 3
M 1 7 0 9 3
N.A. WELDING CABLE MUST BE SIZED FOR CURRENT AND DUTY CYCLE OF APPLICATION.
N.C. INSULATE EACH UNUSED LEAD INDIVIDUALLY.
N.C.
76
82
81
SPARE
2
4
41
42
31
32
GND
21
77
75
REMOTE OUTPUT CONTROL
N.D.
2
4
10K
MIN.
NOT USED ON RANGER POWER SOURCES
42 VAC
115 VAC
N.E.
POWER SOURCE FRAME CONNECTION
N.D. FOR WIRE FEEDERS THAT RETURN A SIGNAL FOR WELDING OUTPUT, USE ISOLATION
RELAY TO CLOSE LEADS 2 & 4.
K867 UNIVERSAL
ADAPTER PLUG
14 PIN
AMPHENOL
{
TO WORK ELECTRODE
TO WORK
N.E. REFER TO POWER SOURCE INSTRUCTION MANUAL FOR MAXIMUM AUXILIARY CURRENT DRAW.
CAUTION :
N.B. USE POLARITY SWITCH TO SET DESIRED POLARITY, POSITION THE OUTPUT SELECTOR SWITCH TO A CV POSITION.
CONNECT TOGETHER FOR
WELDING OUTPUT
WIRE FEEDER VOLTMETER CONNECTION
CONNECTS TO (WORK TERMINAL) OF POWER SOURCE
ELECTRODE CABLE
TO WIRE FEED UNIT
TO
WIRE
FEEDER
TO
K867
ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE WILL CAUSE
DAMAGED. THE ENGINE GOVERNOR SETTING IS PRE-SET AT THE FACTORY - DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN
THE ENGINE WELDER OPERATING MANUAL.
AN INCREASE IN THE THE AC AUXILIARY VOLTAGE. IF THIS VOLTAGE GOES OVER 140 VOLTS, WIRE FEEDER CONTROL CIRCUITS MAY BE
RANGER 9 TO K867 ADAPTER CONNECTION DIAGRAM
WARNING
Do not operate with panels open.
Disconnect NEGATIVE (-) BATTERY LEAD
before servicing.
Do not touch electrically live parts.
Keep guards in place.
Keep away from moving parts.
Only qualified personnel should install,use
or service this equipment.