TOHO ELECTRONICS TTM-339 - Manual (Page 22)

- 22 -
5.5
Common parameter setting mode SET 4 (1)
SET04 Name Setting content Initial value
1 SLH SV limiter upper limit (*2) (*3)
Thermocouple/RTD input (SLL + 5.0) to SV setting range upper limit (

C)
(SLL + 5) to SV setting range upper limit (

C)
1200
Current/voltage input (SLL + 50) to SV setting range upper limit (digit) 12000
2 SLL SV limiter lower limit (*2) (*3)
Thermocouple/RTD input SV setting range lower limit to (SLH - 5.0) (

C)
SV setting range lower limit to (SLH - 5) (

C) 0
Current/voltage input (SLH - 50) to SV setting range lower limit (digit)
3 CNT Control type setting
1 Primary...pid control Secondary---None
1
2 Primary---onoff control Secondary---None
3 Primary---pid control Secondary---pid control
4 Primary---pid control Secondary---onoff control
5 Primary---onoff control Secondary---onoff control
4 DIR Forward/reverse operation setting
0 Reverse operation
0
1 Forward operation
5 MV1 Primary control operating amount 0.0 to 100.0 (%) 0.0
6 TUN Tuning type setting
1 Primary auto-tuning
1 2 Secondary auto-tuning
3 Primary/secondary auto-tuning
7 ATG AT coefficient setting 0.1 to 10.0 (times) 1.0
8 ATC AT sensitivity setting
Thermocouple/RTD input 0.0 to 999.9 (°C) 0 to 999 (°C)
2
Voltage/current input 0 to 9999 (digit)
9 AT1 AT startup screen for PID No. 1 (low
temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is SLL to PM1.
0
10 AT2 AT startup screen for PID No. 2
(intermediate temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is PM1 to PM2.
0
11 AT3 AT startup screen for PID No. 3 (high
temperature)
Startup starts/stops by setting a SV and using the RUN/STOP key.
Characters and PV are alternately displayed in the PV digit during AT.
The SV range is PM2 to SLH.
10
12 ATALL AT startup screen for PID No. 1~3
Use the RUN/STOP key for start and stop.
During the auto tuning, Character//PV is alternately displayed at PV
display, and No. 1 – 3/SV are alternately displayed at SV display.
13 P1 Proportional band setting for PID No. 1 (low temperature) 0.1 to 200.0 (%) 3.0
14 I1 Integral time setting for PID No. 1 (low temperature) 0 to 3600 (seconds) 0
15 D1 Derivative time setting for PID No. 1 (low temperature) 0 to 3600 (seconds) 0
16 PM1 Intermediate point 1 setting for the
PID range
Thermocouple/RTD input SLL to SLH- 5.0 (

C) SLL to SLH - 5 (

C) 0
Current/voltage input SLL to SLH - 50 (digit) 0
17 P2 Proportional band setting for PID No. 2 (intermediate
temperature)
0.1 to 200.0 (%) 3.0
18 I2 Integral time setting for PID No. 2 (intermediate temperature) 0 to 3600 (seconds) 0
19 D2 Derivative time setting for PID No. 2 (intermediate
temperature)
0 to 3600 (seconds) 0
20 PM2 Intermediate point 2 setting for the PID range PM1 to SLH ( 
C) 10
21 P3 Proportional band setting for PID No. 3 (high temperature) 0.1 to 200.0 (%) 3.0
22 I3 Integral time setting for PID No. 3 (high temperature) 0 to 3600 (seconds) 0
23 D3 Derivative time setting for PID No. 3 (high temperature) 0 to 3600 (seconds) 0
24 T1 Primary control proportional cycle 0.1 to 120.0 (seconds) 1.0
25 ARW Anti-reset windup 0.0 to 110.0 (%) Function turned off at 110.0 (%) setting 110.0
26 PS1 Primary control loop abnormalityPV
variation setting
Thermocouple/RTD input 0.0 to 999.9 (

C) or 0 to 999 (

C)
0
Current/voltage input 0 to 9999 (digit)
27 LOP1 Primary control loop abnormality time
setting
0 to 3600 (seconds) 0
28 CMOD Primary control off-point position
selection setting
0 SV unit setting
0
1 Upper
2 Middle
3 Lower
29 C1 Primary control sensitivity control
Thermocouple/RTD input 0.0 to 999.9 (

C) 0 to 999 (

C) 1
Current/voltage input 0 to 9999 (digit) 10
30 CP1 Primary control off-point position
Thermocouple/RTD input -999.9 to 999.9 (

C) -999 to 999 (

C)
0
Current/voltage input -9999 to 9999 (digit)