Document Outline

• Installation and Operation Manual
  • 12/2004 Document Control Number: PRMA-0347-000MD
• Introduction: iSCSI provides storage options
  • Glossary
• 1 Setting up the iPBridge
  • iPBridge1500 features
  • iPBridge 1550 features
• 1.1 ATTO iPBridge 1500E
  • Dimensions
  • Environment
  • Power
  • Reset switch
  • SCSI port
  • Ethernet port
  • Serial port
  • LED indicators
    • Exhibit 1.1-1 iPBridge 1500E board layout
    • Exhibit 1.1-2 iPBridge 1500E board profile and dimensions
  • Installation instructions
• 1.2 ATTO iPBridge 1500D
  • Dimensions
  • Environment
  • Power
  • SCSI port
  • Ethernet port
  • LED indicators
  • Reset switch
    • Exhibit 1.2-1 iPBridge 1500D back panel
  • Installation instructions
• 1.3 ATTO iPBridge 1550E
  • Dimensions
  • Environment
  • Power
  • Reset switch
  • SCSI port
  • Ethernet port
  • Serial port
  • LED indicators
    • Exhibit 1.3-1 iPBridge 1550E board layout
    • Exhibit 1.3-2 iPBridge 1550E board profile and dimensions
  • Installation instructions
• 1.4 ATTO iPBridge 1550D
  • Dimensions
  • Environment
  • Power
  • SCSI port
  • Ethernet port
  • LED indicators
  • Reset switch
    • Exhibit 1.4-1 iPBridge 1550D back panel
  • Installation instructions
• 1.5 Connecting SCSI devices to the SCSI port
  • Cabling
  • Cable types
  • Examples
    • Exhibit 1.5-1 Various types of SCSI operate at different speeds and require different bus lengths to support a certain number of devices.
• 1.6 Configuring the iPBridge
  • Connecting using the GbE port
  • Using ATTO ExpressNAV
  • Connecting using the serial port
  • Using Telnet
• 2 Managing the iPBridge
  • Change default username, password
  • SCSI configuration
  • Ethernet port configuration
  • iSCSI configuration
  • Mapping
  • OEM configuration services
• 2.1 ExpressNAV provides web-based interface
  • Status
  • Serial Port Configuration
  • Ethernet Port Configuration
  • SCSI Configuration
  • iSCSI Configuration
  • Bridge Configuration
  • Mapping
  • Advanced CLI Configuration
  • Restart Firmware
  • Help
• 2.2 CLI provides ASCII-based interface
  • Exhibit 2.2-1 Symbols, typefaces and abbreviations used to indicate functions and elements of the command line interface used in this manual.
• 2.2.1 CLI commands summary
• 2.2.2 General use commands
  • Help
  • Password
  • ReadOnlyPassword
  • ReadOnlyUsername
  • RestoreConfiguration
  • SaveConfiguration
  • Username
  • VerboseMode
• 2.2.3 Diagnostic commands
  • BridgeModel
  • BridgeName
  • Help
  • IdentifyBridge
  • Info
  • IsReserved
  • OEMConfigFile
  • Ping
  • RMON
  • RouteDisplay
  • SCSIPortList
  • SCSITargets
  • CLI Error Messages
    • Exhibit 2.2.3-1 If you enter a parameter for a CLI command incorrectly, the CLI help file will display with the error message:
• 2.2.4 Maintenance commands
  • FirmwareRestart
  • Password
  • Reserve
  • RestoreConfiguration
  • SCSIPortReset
  • SpeedWrite
  • SpeedWriteDefault
  • Username
• 2.2.5 SCSI configuration commands
  • SCSIInitID
  • SCSIPortBusSpeed
  • SCSIPortList
  • SCSIPortReset
  • SCSIPortResetOnStartup
  • SCSIPortSelTimeout
  • SCSIPortSyncTransfer
  • SCSIPortTermination
  • SCSIPortWideTransfer
  • SCSITargets
  • SpeedWrite
  • SpeedWriteDefault
• 2.2.6 Serial port configuration commands
  • SerialPortBaudRate
  • SerialPortEcho
• 2.2.7 Ethernet commands
  • DPMTU
  • EthernetSpeed
  • Exit
  • IPAddress
  • IPDHCP
  • IPGateway
  • IPSubnetMask
  • Password
  • Ping
  • ReadOnlyPassword
  • RMON
  • Username
  • ReadOnlyUsername
  • Exhibit 2.2.7-1 Default historyControl table (buckets and interval in hexadecimal) for the RMON CLI command.
• 2.2.8 iSCSI commands
  • iSCSIAlias
  • iSCSIChap
  • iSCSIChapSecret
  • iSCSIPortNumber
  • iSCSITarget
  • iSNSLoginControl
  • iSNSServer
  • MultiTargetMode
• 2.2.9 Mapping commands
  • AutoMap
  • iSCSITarget
  • MultiTargetMode
  • Route
  • RouteDisplay
  • SCSIInitID
  • SCSITargets
• 2.2.10 Privileged OEM configuration services
  • AutoMapOnBoot
  • ColdReset
  • InquiryProductID
  • InquiryVendorID
  • IqnVendorPrefixID
  • ModelNumber
  • OEMConfigFile
  • ProductID
  • VendorID
• 2.3 Mapping devices
  • Node names
  • Single target mode
  • Use Command Line Interface
    • Exhibit 2.3-1 Physical and virtual connection possibilities with the iPBridge
  • Use the ExpressNAV interface
  • Multiple target mode
  • Use Command Line Interface
  • Example
    • Exhibit 2.3-2 Result of typing SCSITargets 0
    • Exhibit 2.3-3 Result of typing RouteDisplay iSCSI
• 2.4 Updating firmware
• Appendix A Safety standards and compliances
• Appendix B ATTO accessories
• Appendix C Contact ATTO Technology, Inc.