RADWAG WPW 60/H5/K Multifunctional Scales - Manual (Page 6)

- 6 -
27.5.3. I/O diagram ................................................................................................................................................146
7.5.4. Description of input output wires................................................................................................................147 2
27.6. DP1 – module for an additional platform ..............................................................................................................147
27.6.1. Technical specification...............................................................................................................................148
27.6.2. Colours of wires .........................................................................................................................................148
27.6.3. Connecting additional platforms ................................................................................................................149
7.6.4. Installing in PUE C41H housing.................................................................................................................151 2
27.7. RS485 led out via RS 1D gland ............................................................................................................................153
27.7.1. Installing inside the PUE C41H housing ....................................................................................................153
27.7.2. RS 485 - PT0012 cable drawing ................................................................................................................154
28. COM UNICATION PROTOCOL........................................................................................................155 M
28.1. General information ..............................................................................................................................................155
28.2. A set of commands for RS interfaces ...................................................................................................................155
28.3. Respond message format.....................................................................................................................................156
28.4. Command’s description ........................................................................................................................................156
28.4.1. Zeroing.......................................................................................................................................................156
28.4.2. Tarring .......................................................................................................................................................157
28.4.3. Get tare value ............................................................................................................................................157
28.4.4. Set tare value.............................................................................................................................................158
28.4.5. Send the stable result in basic unit ............................................................................................................158
28.4.6. Send the result immediately in basic unit ..................................................................................................159
28.4.7. Get immediate results from both platforms in basic units ..........................................................................159
28.4.8. Send the stable result in current unit .........................................................................................................160
28.4.9. end the result immediately in current unit................................................................................................161 S
28.4.10. Switch on continuous transmission in basic unit .....................................................................................161
28.4.11. Switch off continuous transmission in basic unit .....................................................................................162
28.4.12. Switch on continuous transmission in current unit ..................................................................................162
28.4.13. Switch off continuous transmission in current unit ..................................................................................162
28.4.14. Lock the scale keyboard .........................................................................................................................163
28.4.15. Unlock the scale keyboard ......................................................................................................................163
28.4.16. Initiating of dosing/filling ..........................................................................................................................163
28.4.17. Stop of dosing/filling ................................................................................................................................163
28.4.18. Set lower threshold .................................................................................................................................163
28.4.19. Set upper threshold.................................................................................................................................164
28.4.20. Read lower threshold ..............................................................................................................................164
28.4.21. Read upper threshold..............................................................................................................................164
8.4.22. Send all implemented commands ...........................................................................................................165 2
28.5. Manual printouts / automatic printouts..................................................................................................................165
28.6. Continuous transmission ......................................................................................................................................166
28.7. Configuring printouts.............................................................................................................................................166
29. ERROR MESSAGES..........................................................................................................................167
30. TROUBLE SHOOTING.......................................................................................................................167
31. TECHNICAL PARAMETERS..............................................................................................................168
31.1. Labelling scales WPW/E ......................................................................................................................................168
31.2. Labelling scales WPW/E/H...................................................................................................................................169
32. APPENDIX..........................................................................................................................................170
32.1. Communication with barcode scanners ................................................................................................................170
32.2. Coop ation with „EDYTOR WPW” – PC software tool........................................................................................171 er
32.2.1. Main window ..............................................................................................................................................172
32.2.2. Setting parameters of RS232 ....................................................................................................................172
2.2.3. Setting Ethernet parameters......................................................................................................................173 3
32.3. Creati g and downloading label patterns to the terminal memory ........................................................................175 n
32.3.1. Designing label ..........................................................................................................................................175
32.3.2. Downloading labels‘ patterns to terminals .................................................................................................179
32.3.3. CITIZEN printer setting ..............................................................................................................................181
2.3.4. ZEBRA printer setting ................................................................................................................................182 3
32.4. Example of designing non-standard printouts ......................................................................................................182
32.5. Example of creating a complex report ..................................................................................................................182
32.6. Examples of surge protections .............................................................................................................................185