Pioneer SC-LX90 - Manual (Page 107)

Controlling the rest of your system 12
107
En
3 Press the input source button for the component
you want to control, then press ENTER.
PRES KEY shows in the LCD display. 1
4 Point the two remote controls towards each other,
then press the button that will be doing the learning on
this amplifier’s remote control.
PRES KEY starts flashing to indicate the remote is ready
to accept a signal.
• The remote controls should be 3 cm to 5 cm apart.
5 Press the corresponding button on the other
remote control that is sending (teaching) the signal to
this amplifier’s remote control.
For example, if you want to learn the playback control
signal, press and hold
 briefly. The LCD display will
show OK if the operation has been learned. 2
If for some reasons the operation hasn’t been learned the
LCD will display
ERROR briefly, and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK. 3
Certain buttons represent operations that cannot be
learned from other remote controls. The buttons
available are shown below:
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
7 Press and hold the MULTI OPERATION button for a
couple of seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows
SETUP.
2 Use / to select ERASE, then press ENTER.
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
3 Press the input source button corresponding to the
command to be erased, then press ENTER.
The LCD display flashes
PRES KEY.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows
OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the MULTI OPERATION button for a
couple of seconds when you’re done.
Resetting the remote control presets
This will erase all preset remote control preset codes and
programmed buttons.
4
1 While pressing the MULTI OPERATION button,
press SETUP.
The remote LCD display shows
SETUP.
2 Use / to select RESET, then press ENTER.
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds.
The LCD shows OK to confirm the remote presets have
been erased.
Note
1 • You can’t assign the TUNER, iPod or HOME MEDIA GALLERY buttons.
• The TV CONTROL buttons (TV , TV VOL +/–, TV CH +/–, MUTE and INPUT) can only be learned after the operation selection switch is set to TV.
2 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
3 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings above to erase a programmed button
you’re not using to free up more memory (note that some signals may take more memory than others).
DV D
AV AMPLIFIER
SOURCE
MAIN
MUL TI OPER ATION
A UDIO PAR AMETER TOP MENU ST A TUS THX
CH LEVEL
MENU VIDEO PAR AMETER RETURN
SETUP
ZO N E 2 SOURCE T V
AMP 3
DV R 1 GALLER Y
HOME MEDIA
INPUT SELECT CD
TUNER INPUT
MUTE
MUTE VO L
VO L
TV C ONTROL
CH
iP o d HDMI
STEREO/ F.S.SURR
AU TO / DIRECT
ST ANDARD
A D V S U R R
PHONO
CD-R
DV R 2 VIDEO1
VIDEO2
BD
T V
SA T
SA CD
ENTER
3 cm to 5 cm
DVD
AV AMPLIFIER SOURCE MAIN
MULTI
OPERATION
AUDIO VIDEO
ZONE2
SOURCE TV AMP
3
DVR1
GALLERY
HOME MEDIA
INPUT SELECT
CD
TUNER
INPUT MUTE MUTE
VOL
VOL
TV CONTROL
CH
iPod HDMI PHONO
CD-R
DVR2 VIDEO1 VIDEO2
BD TV SAT
SACD
ENTER
AUDIO
PARAMETER
TOP MENU
STATUS
THX
CH LEVEL
MENU
VIDEO
PARAMETER
RETURN
SETUP
STEREO/
F.S.SURR
SIGNAL SEL SLEEP AUDIO DIMMER
SR+
CLR
SBch PHASE iPod CTRL
A.ATT GENRE HDMI OUT
ENTER
MCACC
DISP
CH
AUTO/
DIRECT STANDARD ADV SURR
4 When Selecting preset codes directly on page 106 are set, all the signals learned in the input source buttons are cleared. This function is convenient when
you want to reset some but not all of input source buttons.
SC_LX90_WY.book Page 107 Wednesday, February 6, 2008 11:49 AM