Pioneer SC-LX90 - Manual (Page 119)

Additional information 13
119
En
Remote control
i.LINK interface
When playing a disc with the
listening mode set to Auto
Surround,
2 PL II or Neo:6
appear on the amplifier.
• Make sure that the amplifier is set to AUTO or DIGITAL (see Choosing the input signal on page 37).
• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is not a
malfunction. Check the disc packaging for details about the audio tracks available.
During playback of a Surround
EX or DTS-ES source on the
SBch
AUTO setting, EX or ES does not
appear, or the signal is not
properly processed.
• The source may be Dolby Surround EX/DTS-ES software, but it has no flag to indicate it is 6.1 compatible.
Set to
SBch ON (see Using surround back channel processing on page 37), then switch to the THX
Surround EX or Standard EX listening mode (see Listening in surround sound on page 34).
During playback of DVD-Audio,
the display shows
PCM.
• This will occur when playing DVD-Audio material over the HDMI connection. This is not a malfunction.
Symptom Remedy
Symptom Remedy
Cannot be remote controlled. • Try replacing the batteries in the remote control (see Loading the batteries on page 7).
• Be sure to operate within 7 m and a 30º angle of the remote sensor on the front panel (see Operating range
of remote control unit on page 31).
• Check that there are no obstacles between the amplifier and the remote control.
• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
• Check the connections of the
CONTROL IN jack (see Operating other Pioneer components with this unit’s
sensor on page 111).
Other components can’t be
operated with the system remote. • If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
• The preset code may be incorrect. Redo the procedure for entering preset codes.
The SR cable is connected, but
the connected components can’t
be operated with the remote. • Reinsert the SR cable, making sure it’s connected to the right jack (see Using this amplifier with a
Pioneer plasma television on page 68).
• Make sure that there is an analog or HDMI connection between the units. This is necessary for the SR
feature to work.
• Check that the other component is made by Pioneer. The SR feature only works with Pioneer equipment.
Symptom Remedy
No sound is output. • Check that the source player is compatible with i.LINK audio.
• Check the output settings of the source player.
• Make sure that
i.LINK or AUTO is selected using the SIGNAL SEL button (see Choosing the input signal
on page 37).
The i.LINK indicator does not
light up even when an i.LINK-
equipped component is selected. • Make sure that i.LINK or AUTO is selected using the SIGNAL SEL button (see Choosing the input signal
on page 37).
• Check the i.LINK connections; use an i.LINK cable of less than 3.5 m.
• Check that the source components conforms to the i.LINK Audio format.
• Make sure that all components connected between the amplifier and the source are switched on.
PQLS OFF or PQLS ON is
displayed temporarily on your
amplifier and the sound output is
discontinued. • During playback through an i.LINK connection, if you change the settings for other i.LINK components,
the sound will be discontinued momentarily. This is not a malfunction.
The program format indicators
don’t disappear when SACD
playback stops. • The program format indicators remain lit until another format source is input. This is not a malfunction.
You can’t get i.LINK to display
when using the
SIGNAL SEL
button.
• Make sure your i.LINK source components are switched on.
• Check that i.LINK is assigned correctly (see
The Input Setup menu on page 94).
After upgrading a component, it
is not recognized and cannot be
selected using the i.LINK
connection. • You may need to reset the i.LINK database memory in the amplifier (use the front panel):
1 In the standby mode, press  STANDBY/ON while pressing SETUP.
2 Use / to select i.LINK DB [NO], then press ENTER.
3 Use / to select Clear, then press ENTER.
4 When Clear? [OK] appears, press ENTER again. Resetting is completed once the normal screen
appears. If DB ERROR is displayed, perform the procedure again.
SC_LX90_WY.book Page 119 Wednesday, February 6, 2008 11:49 AM