Pioneer KRP-600A - Manual (Page 98)

Using the HDMI Control 13
98
En
Setting the HDMI Control
Selecting the input terminal
Select the HDMI terminal to which the external device is connected
in order to use the HDMI Control functions.
1 Press HOME MENU.
2 Select “Setup” ( / then ENTER).
3 Select “Option” ( / then ENTER).
4 Select “HDMI Control Setting” ( / then ENTER).
5 Select “Input Setting” ( / then ENTER).
6 Select “INPUT 1” , “INPUT 3”, “INPUT 4” or “INPUT 5” ( /
then ENTER).
Only the device that supports the HDMI Control and is connected
through the selected INPUT terminal is available for the HDMI
Control functions.
7 Press HOME MENU to exit the menu.
Note
• “INPUT 1” or “INPUT 3” can only be selected when “Enable” has
been selected for the “HDMI Input” menu (see Activating the
HDMI terminal on page 70).
• If you have selected “Off” in step 6, a message “Operations cannot
be carried out. Confirm the HDMI control settings.” appears when
HDMI CONTROL is pressed on the remote control unit.
• If you operate an HDMI supported device(s) using an HDMI
terminal other than the terminal selected in “Input Setting”, a
malfunction may occur. When connecting to any HDMI terminals
other than the terminal selected in “Input Setting”, make sure to
enter the settings of the external device(s) so that the HDMI
Control function does not operate.
Selecting the Power Off Control
You can select whether or not the connected device is turned Off
when the Media Receiver is turned Off.
(factory default is “On”)
1 Repeat steps 1 to 4 in Selecting the input terminal.
2 Select “Power Off Control” ( / then ENTER).
3 Select “On” ( / then ENTER).
4 Press HOME MENU to exit the menu.
Note
• The “Power Off Control” function is valid for the devices
connected to any of HDMI terminals on the Media Receiver.
Selecting the Power-On Ready
You can select whether or not the Media Receiver is turned On
when the connected Pioneer recorder or player is turned On and
images are input to the flat screen TV. (factory default is “On”)
1 Repeat steps 1 to 4 in Selecting the input terminal.
2 Select “Power-On Ready” ( / then ENTER).
3 Select “On” ( / then ENTER).
4 Press HOME MENU to exit the menu.
Selecting the Hold Sound Status
You can select whether or not the sound continues from the
connected Pioneer AV system when the Media Receiver turns On.
(factory default is “Off”)
1 Repeat steps 1 to 4 in Selecting the input terminal.
2 Select “Hold Sound Status” ( / then ENTER).
3 Select “On” ( / then ENTER).
4 Press HOME MENU to exit the menu.
Note
• To have the sound continue when the Media Receiver turns On,
confirm that the Switch to TV Sound option appears on the
HDMI Control menu before turning the Media Receiver Off (see
page 99).
Power On/Off Test
You can confirm if the Power On/Off control function is effective
between the Media Receiver and the connected device.
1 Repeat steps 1 to 4 in Selecting the input terminal.
2 Select “Power On Test” or “Power Off Test” ( / then
ENTER).
A list containing devices appears when multiple HDMI devices are
connected to the HDMI terminals.
3 Select the desired device ( / then ENTER).
4 Press HOME MENU to exit the menu.
Note
• Devices that can be checked for Power On/Off Test are those
connected to HDMI terminals as set in “Input Setting”.
• If the Power On/Off Test fails, check for the connection and
setting.
Power Off Test
Power On Test
Input Setting : Off
Power Off Control : Off
Power-On Ready : Off
Hold Sound Status : Off
KRP-600A_500A.book Page 98 Monday, September 8, 2008 10:31 AM