Pioneer VSX-D510 - Manual (Page 20)

20
En
Displays & Controls
Remote Control
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
SOURCE CLASS MPX BAND
LOUDNESS FUNCTION MUTING
RECEIVER
D.ACCESS CHANNEL
ATT
VOL
MENU
TOP
MENU
VOL
CH
2 DSP MODE MIDNIGHT 5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL EFFECT
ENTER
ENTER
FQ
FQ
ST ST
FL
DIMMER
REMOTE
SETUP
MASTER
VOLUME
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
TV CONTROL
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER TUNER TV CONT
Î
1 2 3 4
1 ¡ 4 ¢
7 8 3
5 6 7 8
9 0 ‡
2
6
8
5
1
3
0
9
-
=
!
@
~
#
%
$
^
7
4
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the stated
mode.
For other equipment controls, see Controlling the
Rest of Your System on pages 31-32.
2 RECEIVER button (see page 13)
Use this button when setting up the surround sound
for the receiver.
3 NUMBER/MODE buttons (see pages 26, 31, 32)
Use the number buttons to select the radio frequency
in tuner DIRECT ACCESS mode or the tracks in CD,
DVD mode etc.
Also, buttons marked with the following names have
special functions. If you try to use one of these
functions but the display flashes it means that
function cannot be used in the current mode (for
example DSP modes cannot be used when 5.1 CH
setting is on).
2 (see pages 17, 25)
Use to put receiver in DOLBY DIGITAL, DOLBY
SURROUND and DTS modes. To use first press the
RECEIVER button then operate this button.
DSP mode (see pages 24)
Use to put receiver in one of the DSP modes. To use
first press the
RECEIVER button then operate this
button.
MIDNIGHT (see page 24)
Use to put receiver in MIDNIGHT mode. To use first
press the
RECEIVER button then operate this button.
5.1 ch (see page 24)
When the DVD/LD or DVD 5.1 CH function is
selected each press switches the DVD/LD input
between DVD/LD and DVD 5.1 CH. To use first press
the
RECEIVER button then operate this button.
CHANNEL SELECT (see page 17-memo)
Use to select a speaker when setting up the surround
sound of the receiver. To use first press the
RECEIVER button then operate this button.
TEST TONE (see page 17)
Use to sound the TEST TONE when setting up the
surround sound of the receiver. To use first press the
RECEIVER button then operate this button.
ATT
If the Overload indicator lights often, use to attenuate
(lower) the level of an analog input signal to prevent
distortion. To use, press the
RECEIVER button first,
then press this button.
CHANNEL LEVEL +/– (see page 17-memo)
Use to set up the levels of the surround sound of the
receiver. To use first press the
RECEIVER button then
operate this button.
SIGNAL SELECT (see page 23)
Use to select the proper signal (analog, digital) for the
source your are inputting. To use first press the
RECEIVER button then operate this button.
4 THE FOLLOWING FOUR SETS OF BUTTONS
ARE DEDICATED TV CONTROL. THEY ARE
ONLY USED FOR CONTROLLING YOUR TV.
FUNC button
Use select the TV function.
TV POWER button
Use to turn on the power of the TV.
TV CHANNEL +/– buttons
Use to change channels on your TV.
TV VOLUME +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with your
DVD player.
6 SOURCE button
Use to turn on/off the components connected to the
receiver.