Pioneer VSX-D510 - Manual (Page 26)

26
En
07
Finding a Station
The following steps show you how to tune in to FM and
AM radio broadcasts using the automatic (search) and
manual (step) tuning functions. If you already know the
exact frequency of the station you want to listen to, see
Tuning Directly to a Station below. Once you are tuned
to a station you can memorize the frequency for recall
later—see Memorizing Stations on page 27 for more on
how to do this.
Using the Tuner
1 Press the MULTI CONTROL TUNER button
on the remote control or turn the MULTIJOG
DIAL on the receiver to select the tuner
mode.
2 Use the BAND button to change the band
(FM or AM), if necessary.
Each press switches the band between FM and AM.
3 Tune to a station.
Automatic tuning
To search for stations in the currently selected band,
press and hold either the
FQ. + or FQ. – button for
about a second. The receiver will start searching for
the next station, stopping when it has found one.
Repeat this step to search for other stations.
Manual tuning
To change the frequency one step at a time, press the
FQ. + / FQ. – (
5∞) buttons.
High speed tuning
Press and hold the
FQ. + or FQ. – button for high
speed tuning, releasing the button once the desired
frequency is reached.
MPX mode
If the TUNED or STEREO indicators don't light when
tuning to an FM station because the signal is weak, press
the
MPX button to switch the receiver into mono
reception mode. This should improve the sound quality
and allow you to enjoy the broadcast.
2
1
MPX
3
Tuning Directly to a Station
Sometimes, you'll already know the frequency of the
station you want to listen to. In this case, you can simply
enter the frequency directly using the number buttons
on the remote control (this function is not available
using the front panel controls of the receiver).
1 Press the MULTI CONTROL TUNER button
on the remote control or turn the MULTIJOG
DIAL on the receiver to select the tuner
mode.
2 Press the BAND button to select either FM
or AM.
Each press switches the band between FM and AM.
3 Press D.ACCESS ( DIRECT ACCESS ).
4 Use the number buttons to enter the
frequency of the radio station.
Example: To tune to 106.00 (FM), press 1 – 0 – 6 –
0 – 0
SP A STEREO
TUNED
MEMO:
• If you make a mistake while inputting the frequency,
press the D.ACCESS button twice to cancel the
frequency and start again.
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
LOUDNESS FUNCTION MUTING
D.ACCESS CHANNEL
ATT
VOL
MENU
TOP
MENU
VOL
CH
2 DSP MODE MIDNIGHT 5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL EFFECT
ENTER
ENTER
FQ
FQ
ST ST
FL REMOTE MASTER
TV CONTROL
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER TUNER TV CONT
1 2 3 4
1 ¡ 4 ¢
7 8 3
5 6 7 8
9 0 ‡
SOURCE CLASS MPX BAND
2
1
3
4
MULTI CONTROL
DVD/LD TV/SAT VCR/DVR CD
LOUDNESS FUNCTION MUTING
RECEIVER
D.ACCESS CHANNEL
ATT
VOL
MENU
TOP
MENU
VOL
CH
2 DSP MODE MIDNIGHT 5.1CH
CD-R/
TAPE/MD
CHANNEL
SELECT
CHANNEL
LEVEL EFFECT
ENTER
ENTER
FQ
FQ
ST ST
FL
DIMMER
REMOTE
SETUP
MASTER
VOLUME
TV CONTROL
FUNC
10 DISC
SIGNAL
SELECT
TEST
TONE
RECEIVER TUNER TV CONT
1 2 3 4
1 ¡ 4 ¢
7 8 3
5 6 7 8
9 0 ‡
SOURCE CLASS MPX BAND