Environmental Express SPE-Express with Cover - Manual (Page 21)

Environmental
Express,
Inc.
800.343.5319/843.881.6560 20
• Select the desired number of hexane sprays per rinse cycle.
• Select the desired hexane drain time in seconds.
• Select the desired number of rinse cycles.
• Select the desired activated vacuum time in seconds.
• Select the desired deactivated vacuum time in seconds.
• Select the desired number of total vacuum cycles.
• Select the desired vacuum dry time in seconds.
• Select the desired nitrogen purge time in seconds.
When entering the “Hexane Spray Volume”, and the “Hexane Sprays per Rinse Cycle”, the total
hexane spray volume cannot exceed 30mL or drop below 9mL.The warning message will appear if
the requirements are not met.
When entering the “Hexane Spray Volume”, the “Hexane Sprays per Rinse Cycle”, and “Number of
Rinse Cycles” text box, the total hexane volume cannot exceed 120mL or drop below 27mL. The
warning message will appear if the requirements are not met.
2.3.6.5 Solvent Evaporation
The software will automatically calculate the hexane evaporation time based on the total amount
of hexane used in the method. This evaporation time will be added to the end of the test prior to
completion.
• Press the “Load” button to import pre-created parameters into the system, or press the
F1 key.
• Press the “Save” button to save the parameters shown, or press the F2 key.
• Press the “Save As” button to save the parameters shown under a different file name, or
press the F3 key.
• Press the “Print” button to print the parameters shown, or press the F4 key.
• Press the “Exit” button to exit, or press the Escape key.
Use the arrow controls to:
Select the desired hexane spray •
volume in milliliters per spray.
Select the desired number of •
hexane sprays per rinse cycle.
Select the desired hexane drain •
time in seconds.
Select the desired number of •
rinse cycles.
Select the desired activated •
vacuum time in seconds.
Select the desired deactivated •
vacuum time in seconds.
Select the desired number of •
total vacuum cycles.
Select the desired vacuum dry •
time in seconds.
Select the desired nitrogen •
purge time in seconds.
Please note: When entering the
“Hexane Spray Volume”, and the
“Hexane Sprays per Rinse Cycle”, the
total hexane spray volume cannot
exceed 30mL or drop below 9mL.
The warning message, Figure 19,
will appear if the requirements are
not met.
When entering the “Hexane Spray
Volume”, the “Hexane Sprays per Rinse
Cycle”, and “Number of Rinse Cycles”
text box, the total hexane volume
cannot exceed 120mL or drop below
27mL. The warning message, Figure
20, will appear if the requirements are
not met.
e. Solvent Evaporation
In this area, the user may enter the
parameter for solvent evaporation.
Use the arrow controls to select •
the desired evaporation time in
minutes.
f. Press the “Load” button to import
pre-created parameters into the
system, or press the F1 key.
Environmental Express • 16 800.745.8218 / 843.576.1147 / www.environmentalexpress.com
Initial System Setup Method Creation
Figure 18
Figure 20
Figure 19 g. Press the “Save” button to save
the parameters shown, or press the
F2 key.
h. Press the “Save As” button to
save the parameters shown under
a different file name, or press the
F3 key.
i. Press the “Print” button to print
the parameters shown, or press the
F4 key.
j. Press the “Exit” button to exit, or
press the Escape key.
Use the arrow controls to:
Select the desired hexane spray •
volume in milliliters per spray.
Select the desired number of •
hexane sprays per rinse cycle.
Select the desired hexane drain •
time in seconds.
Select the desired number of •
rinse cycles.
Select the desired activated •
vacuum time in seconds.
Select the desired deactivated •
vacuum time in seconds.
Select the desired number of •
total vacuum cycles.
Select the desired vacuum dry •
time in seconds.
Select the desired nitrogen •
purge time in seconds.
Please note: When entering the
“Hexane Spray Volume”, and the
“Hexane Sprays per Rinse Cycle”, the
total hexane spray volume cannot
exceed 30mL or drop below 9mL.
The warning message, Figure 19,
will appear if the requirements are
not met.
When entering the “Hexane Spray
Volume”, the “Hexane Sprays per Rinse
Cycle”, and “Number of Rinse Cycles”
text box, the total hexane volume
cannot exceed 120mL or drop below
27mL. The warning message, Figure
20, will appear if the requirements are
not met.
e. Solvent Evaporation
In this area, the user may enter the
parameter for solvent evaporation.
Use the arrow controls to select •
the desired evaporation time in
minutes.
f. Press the “Load” button to import
pre-created parameters into the
system, or press the F1 key.
Environmental Express • 16 800.745.8218 / 843.576.1147 / www.environmentalexpress.com
Initial System Setup Method Creation
Figure 18
Figure 20
Figure 19 g. Press the “Save” button to save
the parameters shown, or press the
F2 key.
h. Press the “Save As” button to
save the parameters shown under
a different file name, or press the
F3 key.
i. Press the “Print” button to print
the parameters shown, or press the
F4 key.
j. Press the “Exit” button to exit, or
press the Escape key.