Soleus GPS Draft (SG200) - Manual - Manual (Page 8)

GPS Draft – Instruction Manual
ALARM mode
• Press S7 from Data mode to enter ALARM mode. The Bike computer will display
ALARM and then Alarm 1 time.
• Press S5 to view the other alarm settings and Chime setting. The computer has 5 alarms
that can be set individually. After alarm 5, pressing S5 will show the Chime view.
• Press S1 to turn ON or OFF the selected alarm or CHIME
• Alarm will sound for 20 seconds at alarm time. Pressing any button will stop the alarm
sound without the button function. When Alarm is ON, the alarm icon is displayed in all
modes.
Alarm setting mode:
•
Press and hold S11 from any alarm views to enter Alarm setting mode. The computer
will display HOLD TO SET and then AL 1 will start to blink.
• Press S1/S11 to change the alarm number.
• Press S5 to enter. Hour digit will start to blink.
• Press S1/S11 to change the hour digits.
• Press S5 to enter. Minute digits will start to blink.
• Press S5 to enter. T1 to T2 will start to blink. This number means the alarm is referred to
Time 1 or Time 2.
• Press S1/S11 to change the number.
• Press S5 to enter. OFF or ON will start to blink.
• Press S1/S11 to change. Press S5 to enter.
• Press S7 to exit setting mode.
SET mode
Press S7 from ALARM mode to SET mode. 1.5 seconds later the Bike computer will display
the setting options. The following sequence follows; AUTO LAP, TIME, UNIT, USER, NIGHT,
CONTRAST, CHIME, ALARM, ODO and VIEW. Press S1/S11 to select then press S5 to
enter. Press S7 to exit setting to Time mode.
Setting the AUTO LAP:
• While AUTO LAP is blinking, press S5 to set AUTO LAP. 1 KM will start to blink.
• Press S1/S11 to select Auto lap setting options (0.5, 1, 2, 3, 4, 5 and OFF). Press
S5/S7 to enter the selected setting. ALERT ON or OFF will start to blink.
• Press S1/S11 to change setting. Press S5/S7 to enter and go back to AUTO LAP
setting screen.
• Press S7 to exit setting.
Setting the TIME:
• Press S5 while TIME is blinking. T1 or T2 will start to blink.
• Press S1/S11 to select which time to set. Press S5 to enter. GPS or MANUAL will start to
blink.
• Press S1 or S11 to select GPS or MANUAL setting. Press S5 to enter selected setting.
Note that you have two options in setting the Bike computer, GPS or MANUAL. In manual
setting, you can manually set the time. If you select the GPS option, the Bike computer will
be automatically set base on the data and time data from GPS satellites.
GPS setting:
o Select TIME ZONE by pressing S1/S11 and then press S5 to enter. There are 36 city
codes to select.
o Select DST ON or OFF by pressing S1/S11 and then press S5 to enter.
o Select 12H or 24H format setting by pressing S1/S11. Press S5 to enter.
o Select M-D or D-M display format by pressing S1/S11. Press S5 to enter and go back
to TIME setting screen.
o Press S7 to exit.
MANUAL setting:
o Set the HOUR by pressing S1/S11 to change digit then press S5 to enter.
o Set the MIN by pressing S1/S11 to change digit then press S5 to enter.
o Set the SEC by pressing S1/S11 to change digit then press S5 to enter.
o Set the YEAR by pressing S1/S11 to change digit then press S5 to enter.
o Set the MONTH by pressing S1/S11 to change digit then press S5 to enter.
o Set the DAY by pressing S1/S11 to change digit then press S5 to enter.
o Set the 12/24H by pressing S1/S11 to change digit then press S5 to enter.
o Select M-D or D-M display format by pressing S1/S11. Press S5 to enter and go back
to TIME setting screen.
o Press S7 to exit
Setting the UNIT:
• Press S5 while UNIT is blinking. The computer will display KM or MI
• Press S1/S11 to select KM or Mi. Press S5/S7 to confirm.
• Press S7 to exit setting.
Setting the USER’s Information:
• Press S5 while USER is blinking. MALE or FEMALE will start to blink.
• Press S1/S11 to change the values. Press S5/S7 to confirm. AGE digit will start to blink.
• Press S1/S11 to change the age digit. Press S5/S7 to confirm. WEIGHT digits will start
to blink.
• Press S1/S11 to change the weight digit. Press S5/S7 to confirm. HEIGHT digits will start
to blink.
• Press S1/S11 to change the height digit. Press S5/S7 to confirm and go back to USER
setting screen.