Soleus GPS Draft (SG200) - Manual - Manual (Page 9)

GPS Draft – Instruction Manual
• Press S7 to exit setting.
Setting the NIGHT function:
•
Press S5 while NIGHT is blinking. The computer will display 10 sec, 20 SEC, or ON
blinking.
• Press S1/S11 to change the setting (10 sec, 20 sec, or NIGHT ON).
• While on 10 SEC or 20 SEC setting, Press S5 to accept the setting and go back to
NIGHT setting screen.
• While on NIGHT ON setting screen Press S5 to accept the ON setting. The computer will
display the START TIME.
• Press S1/S11 to toggle between START TIME and END TIME.
• Press S5 or 3 seconds auto to set the START TIME. Hour digit will start to blink.
• Press S1/S11 to change the hour setting.
• Press S5 to change the MINUTE. Minute digits will start to blink.
• Press S1/S11 to change the minute setting.
• Press S5 to go back to START TIME setting screen.
• Press S1/S11 within 3 seconds to set the END TIME. Hour digit will start to blink. The
computer will automatically enter the HOUR digit of START TIME after 3 seconds.
• Follow the procedure in setting the START TIME.
• Press S7 to exit.
Setting the CONTRAST:
•
Press S5 while CONTRAST is blinking. The computer will display ON CHIME or OFF
CHIME.
• Press S1/S11 to change.
• Press S5/S7 to exit
Setting the CHIME:
•
Press S5 while CHIME is blinking. The computer will display the contrast value.
• Press S1/S11 to change the contrast value. Contrast range is 10 to 100%
• Press S5/S7 to exit
Setting the ALARM:
The Bike computer has 5 alarms which can be set for Time 1 or Time 2.
•
Press S5 while ALARM is blinking. AL 1 will start to blink.
• Press S1/S11 to change the alarm number.
• Press S5 to enter. Hour digit will start to blink.
• Press S1/S11 to change the hour digits.
• Press S5 to enter. Minute digits will start to blink.
• Press S5 to enter. T1 to T2 will start to blink. This number means the alarm is referred to
Time 1 or Time 2.
• Press S1/S11 to change the number.
• Press S5 to enter. OFF or ON will start to blink.
• Press S1/S11 to change. Press S5 to enter.
• Press S7 to exit setting mode.
Setting the ODOMETER:
• Press S5 while ODO is blinking. The first digit will start to blink.
• Press S1/S11 to change the digit. Press S5/S7 to enter. The next digit will start to blink.
• Repeat the procedure until you are finished setting all the digits.
• Press S7 to exit setting.
NOTE: You cannot set the ODO if the chrono is running.
Weigh range: 20 to 255 Kg (44 to 561 Lbs) default is 65 Kg (143 lbs)
Height range: 91-241 cm (2’11”-8’0” ft’ inch”) default 170 cm
Age Range: 7 to 99. Default is 25
Sex/ Gender: Male or Female, default is Male
Units: KM/M/KG or MI/FT/LBS
Setting VIEW:
You can set the information displayed in Line 2 & Line 3 in BIKE mode in these setting
screens.
•
Press S5 while VIEW is blinking. The computer will display the VIEW / DIST / CHRO
screen and CHRO is blinking.
• Press S5 to toggle between Line 2 & Line 3 blinking.
• Press S1/S11 to change the information to display in that line. You can select any of
the following information to be displayed: Chrono, Distance, Calorie, ODO, & Clock.
• Press S7 to exit
Battery:
The Bike computer is using a rechargeable Lithium Ion battery that will require approximately
4.0 hours charging time using the USB cable. While battery is charging, the Bike computer
cannot be used and all buttons are disabled. User needs to recharge the battery when the
Bike computer indicates a “low battery”.
Battery Life ( full charge ): 8 hrs typical (continuous GPS).