Panasonic OMNIVISION VHS PV-M2058 - Manual (Page 29)

In order for the Combination VCR to read the VCR Ptus+ code, some setup is required. A Guide (VCR Plus+) channel
number is assigned to each local broadcast and cable station. Because this number sometimes differs from the channel
your TV receives the station on, it is necessary to program the Combination VCR with local channel information.
VCR Plus+ Channel Setup
For Connection Type B (page 28) only
• Before you begin, complete the Channel Setup
Preparations below left.
Important Note:
If your Combination VCR Connection type changes, from
Type A to B, repeat step 4 of previous page, select “NO.”
2
3
4
5
b
C
d
3 Press ACTION to display
the MAIN MENU.
b
Press
AT
◄ ► t o select
“CH,” and then press
ACTION to display the
SET UP CHANNEL
screen.
SELECT:* ▼ ► KEY
SET :ACTION KEY
Model PV-M2058 remote is shown here.
Press
AT
to select “VCR
Plus+CH SET UP,” and
then press ► to display
the VCR Plus+ CH SET
UP screen.
------- SET UP CHANNEL --------------
ANTENNA : CABLE
ALTTO SET
CHANNEL CAPTION
CABLE BOX SET UP
^aai! lEiisa
SELECT:* ▼ KEY
SET :► KEY
END :ACT I ON KEY
Channel Setup Preparations
NOTE:
Complete the steps on this page if your Combination
VCR hook-up resembles “B” on page 28.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step “d” at right.
You will need the following to complete the list:
• A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart is
supplied by your cable company.
• A list of Guide (VCR Plus-i-) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found in
selected newspapers.
1
Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2
In the middle column, fill in each station’s
assigned Guide (VCR Plus+) number found in TV
Guide, newspapers, etc.
3
In the right column, fill in the channel number that
your TV receives the station on from your channel
line-up.
< EXAMPLE ONLY >
Broadcast or Assigned Guide Channel No. your
Cable Station (VCR Plus-i-) TV receives the
Name Channel No. station on
HBO 33 15
Nickelodeon 38 20
CBS 34 04
FOX 11
IMPORTANT NOTE:
For step “d”, use the list you prepared at left.
You may leave lines blank if you don’t receive
that station, or if the GUIDE CH number and the
CABLE (or TV) CH numbers are the same.
d Press ► to move the
shaded area to the right
side.
VCR PIUS+ CH SET UP
GUIDE CH CABLE CH
ED
02
SELECT;* ▼ KEY
SET ;► KEY
END :ACT I ON KEY
Then, press AV to change
the CABLE (or TV) CH
number.
Next, press ◄ to set the CABLE (or TV) CH number.
Now, press
AT
to continue. Repeat this operation
until the list is complete.
To Make Corrections
Press
AT
and ► to select the incorrect CABLE or TV
CH number.
Then, press
AT
to change, or ADD/DLT to delete the
channel.
G Press ACTION three times to exit the VCR
P\us+
CH SET UP mode.
• Make each entry within 5 minutes or the
Combination VCR will leave this mode.
• Once local channels have been
programmed, they will stay in memory, even
in the case of a power failure.
29