E “additional rf setup” illu, D 10, respect, 10 fo – Crestron electronic STX-1700CXP User Manual
Page 14: Way rf wireless touchpanel crestron stx-1700cxp, Key click setup
2-Way RF Wireless Touchpanel
Crestron STX-1700CXP
10
• 2-Way RF Wireless Touchpanel: STX-1700CXP
Operations Guide - DOC. 6144
ADDITIONAL RF SETUP
Press the ADDITIONAL SETUP button to display the ADDITIONAL RF SETUP
screen. In situations where two or more touchpanels are in close proximity and could
conflict with each other, press the SET LOW POWER button to reduce the
touchpanel’s power and minimize the possibility of interference. The factory default
setting is SET HIGH POWER.
Use the PREVIOUS and NEXT buttons to choose the desired frequency band. The
choices correspond with the names shown in the following table. The table shows
the 802.11b channels within each band that are occupied by the STX-1700CXP.
Selection of a band is based on a number of factors, including the need to avoid
interference with nearby RF devices, and compliance with local communication
laws. In the US, Crestron recommends using Bands 5 (USA comp 1) through 9
(USA comp 5). Bands 1 through 4 (France, Spain, Japan, and Canada) are intended
for use in Cresnet systems outside the US. The default setting is Band 0, USA
(original), which is not Wi-Fi friendly. At this setting, the touchpanel can
communicate with a TPS-RFGWX gateway whether it is Wi-Fi friendly or not, since
Band 0 is the default for both versions of the gateway. Note that the touchpanel and
gateway must be set to the same band in order to communicate.
1
2
3
4
5
6
7
8
9 10 11 12 13 14
0
2400-2474 USA (original)
•
•
•
•
•
•
•
•
•
•
•
•
•
1
2448-2474
France
•
•
•
•
•
•
•
2
2448-2474
Spain
•
•
•
•
•
•
•
3
2471-2497
Japan
•
•
•
•
4
2452-2477
Canada
•
•
•
•
•
•
•
5
2400-2425 USA (comp 1)
•
•
•
•
•
6
2409-2435 USA (comp 2)
•
•
•
•
•
•
•
7
2419-2445 USA (comp 3)
•
•
•
•
•
•
•
•
8
2430-2455 USA (comp 4)
•
•
•
•
•
•
•
•
•
9
2440-2465 USA (comp 5)
•
•
•
•
•
•
•
•
•
Occupied 802.11b Channels
Band
#
Freq.
Range
(MHz)
Band Name
In the table, a bullet (•) indicates channels that are used by the STX-1700CXP. The unmarked channels
can be used by other devices communicating near the Cresnet system, thus minimizing interference.
After the Cresnet ID, RF ID, RF CHANNEL, and Band settings have been verified,
touch the Return button at the bottom of the screen to save settings and display the
SELECT INTERFACE screen. Touch Return again to display the SETUP MENU.
KEY CLICK SETUP
Key Click Setup
From the SETUP MENU, press the Key Click Enabled button to open KEY CLICK
SETUP screen. (If the function is currently disabled, the button legend is “Key Click
Disabled.”) To enable an audible tone (beep) when the touchpanel buttons are
pressed, select among the Short, Med, or Long KEY CLICK ENABLE/LEN buttons
to set the duration of the tone. The touchpanel responds with a corresponding signal.
To disable the feature, select Click Off.
Use the KEY CLICK VOLUME UP and DOWN buttons to increase and decrease the
volume of the signal. The area to the right of the buttons shows the relative volume
from 0% to 100%, both as a numeric value and, for a quick visual reference, as an
analog bar.
Select the Return button to return to the SETUP MENU.