Pinout assignments - common connectors 43, Appendix – Hatteland Display HM C01 (Rugged) User Manual
Page 43
Pinout Assignments - Common Connectors
43
IND100241-22
Appendix
Additional connector pinouts may be available in third party motherboard manuals, primarily for computers only.
Please see manual/drivercd delivered with your product or own section in this user manual.
9-pin Amplifi ed Mono/Stereo Audio Out, DSUB Female
Type Number “HT 00235 OPT-A1”
5 4 3 2 1
9 8 7 6
PIN 01 LAUDR Left Audio Return*
PIN 02 LAUD
Left Audio*
PIN 03 RAUDR Right Audio Return
PIN 04 RAUD
Right Audio
PIN 05 N/C
No internal connection
PIN 06 N/C
No internal connection
PIN 07 N/C
No internal connection
PIN 08 N/C
No internal connection
PIN 09 N/C
No internal connection
*For Mono: connect pin 01 and 02 only
25-pin Female Parallel (Optional for selected computers)
13 12 11 10 9 8 7 6 5 4 3 2 1
25 24 23 22 21 20 19 18 17 16 15 14
Pin 01 STROBE
This signal indicates to the printer that data at PD7..0 are valid.
Pin 02 DATA0
Parallel data bus from PC board to printer. The data line are able to operate in PS/2 compatible bi-directional mode.
Pin 03 DATA1
Same as Pin 02
Pin 04 DATA2
Same as Pin 02
Pin 05 DATA3
Same as Pin 02
Pin 06 DATA4
Same as Pin 02
Pin 07 DATA5
Same as Pin 02
Pin 08 DATA6
Same as Pin 02
Pin 09 DATA7
Same as Pin 02
Pin 10 ACK
Signal from printer indicating that the printer has received the data and is ready to accept further data.
Pin 11 BUSY
Signal from printer indicating that the printer cannot accept further data.
Pin 12 PE
Signal from printer indicating that the printer is out of paper.
Pin 13 SELECT
Signal from printer to indicate that the printer is selected.
Pin 14 AUTO FEED This active low output causes the printer to add a line feed after each line printed.
Pin 15 ERR#
Signal from printer indicating that an error has been detected.
Pin 16 INIT#
This active low output initialises (resets) the printer.
Pin 17 SLIN#
Signal to select the printer sent from CPU board to printer.
Pin 18 GND
Ground
Pin 19 GND
Ground
Pin 20 GND
Ground
Pin 21 GND
Ground
Pin 22 GND
Ground
Pin 23 GND
Ground
Pin 24 GND
Ground
Pin 25 GND
Ground
Analog RGB/VGA, 15-pin DSUB High Density Female
5 4 3 2 1
15 14 13 12 11
10 9 8 7 6
PIN 01 RED
Red, analog
PIN 02 GREEN
Green, analog
PIN 03 BLUE
Blue, analog
PIN 04 ID2/RES
Reserved for monitor ID bit 2 (grounded)
PIN 05 GND
Digital ground
PIN 06 RED_RTN
Analog ground red
PIN 07 GREEN_RTN Analog ground green
PIN 08 BLUE_RTN
Analog ground blue
PIN 09 KEY/PWR
+5V power supply for DDC (optional)
PIN 10 GND
Digital ground
PIN 11 ID0/RES
Reserved for monitor ID bit 0 (grounded)
PIN 12 ID1/SDA
DDC serial data
PIN 13 HSYNC.
Horizontal sync or composite sync, input
PIN 14 VSYNC.
Vertical sync, input
PIN 15 ID3/SCL
DDC serial clock