Flowserve MENBLOC 60Hz - Manual (Page 11)

MENBLOC 60Hz USER INSTRUCTIONS ENGLISH 71559945 - 02/13
Page 11 of 36 flowserve.com
2.2 Handling
2.2.1 General instructions concerning handling
Boxes, crates, pallets or cartons may be unloaded
using fork-lift vehicles or slings dependent on their
size and construction. See 2.3.1 for positioning of
slings.
To lift heavy pieces above 25 kg (55 lb), use a winch
adapted to the mass and in accordance with the
current local regulations.
To lift machines or pieces with one or several
suspension rings, only use hooks and chains in
compliance with the local regulations concerning
safety. Never put cables, chains or ropes directly on
or in the suspension rings. Cables, chains or lifting
ropes must never present excessive bending.
Never bend the lifting hooks, suspension rings,
chains, etc., which should only be made to endure
stresses within, calculated limits. Remember that the
capacity of a lifting device decreases when the
direction of the lifting force direction makes an angle
with the device axis.
To increase the safety and the efficiency of the lifting
device, all the lifting elements must be as
perpendicular as possible. If necessary a lifting
beam can be placed between the winch and the
load.
When heavy pieces are lifted up, never stay or work
under the load or in the area, which could be in the
path of the load if it were to swing or fall away.
Never leave a load hanging from a winch. The
acceleration or the slowing-down of lifting equipment
must stay in the safety limits for the staff.
A winch must be positioned in such a way that the
load will be raised perpendicularly. Where possible
necessary precautions must be taken to avoid the
swing of the load, using for example two winches
making approximately the same angle, below 30°,
with the vertical.
2.2.2. Pump unit and motor masses
4 Poles
North America Metric Unit
mass
Motor
mass
MENBLOC (Hp) MENBLOC (kW)
kg lb kg lb
2 x 1¼ - 5-3/4 50-32-125/0.55-4 25 55 11 24
2 x 1¼ x 6-3/4 50-32-160/0.55-4 35 77 11 24
2 x 1¼ x 8-11/2 50-32-200/1.2-4 46 101 18 40
2 x 1¼ x 8L-2 50-32-200L/1.5-4 50 110 17 37
2½ x 1½ x 5-3/4 65-40-125/0.55-4 31 68 11 24
2½ x 1½ x 6-1 65-40-160/0.75-4 33 73 13 29
2½ x 1½ x 8L-2 65-40-200L/1.5-4 49 108 17 37
2½ x 1½ x 10-3 65-40-250/2.2-4 63 139 23 51
2½ x 1½ x 10L-5 65-40-250L/4-4 76 168 29 64
2½ x 2 x 5-1 65-50-125/0.75-4 35 77 13 29
2½ x 2 x 6-11/2 65-50-160/1.2-4 52 115 18 40
2½ x 2 x 8L-5 65-50-200L/3.3-4 63 139 25 55
2½ x 2 x 10L-5 65-50-250L/4-4 76 168 29 64
3 x 2½ x 5-11/2 80-65-125/1.2-4 47 104 18 40
3 x 2½ x 6-2 80-65-160/1.5-4 53 117 17 37
3 x 2½ x 6-3 80-65-160/2.2-4 59 130 23 51
3 x 2½ x 8L-5 80-65-200L/3.3-4 70 154 25 55
3 x 2½ x 8L-5 80-65-200L/4-4 74 163 29 64
3 x 2½ x 10L-10 80-65-250L/8.2-4 128 282 65 143
3 x 2½ x 13L-20 80-65-315/15-4 * 268 591 163 359
4 x 3 x 6-2 100-80-160/1.5-4 56 123 17 37
4 x 3 x 6-3 100-80-160/2.2-4 62 137 23 51
4 x 3 x 8L-10 100-80-200L/8.2-4 121 267 65 143
4 x 3 x 10L-10 100-80-250L/8.2-4 134 295 65 143
4 x 3 x 10L-15 100-80-250L/12-4 137 302 68 150
4 x 3 x 13-20 100-80-315/15-4* 277 611 163 359
5 x 4 x 8L-10 125-100-200L/8.2-4 137 302 65 143
5 x 4 x 10L-15 125-100-250L/12-4 146 322 68 150
5 x 4 x 13-30 125-100-315/22-4* 320 705 196 432
5 x 4 x 13L-40 125-100-315L/30-4* 382 842 256 564
6 x 5 x 10L-20 150-125-250L/15-4* 283 624 163 359
6 x 5 x 10L-30 150-125-250L/22-4* 317 699 196 432
* IP 55 motor (added pump shaft)
Pieces below 25 kg (55 lb) can be manually
handled but operators should wear protective gloves
and exercise caution.