Roland JUPITER-X Synthesizer - Manual (Page 28)

JUPITER-X Owner's Manual Ver. 1.5 and later
28
Parameter
[1] knob
Value
[2] knob
Explanation
Knob Mode DIRECT, CATCH
Specifies whether the parameter value
corresponding to a controller is immediately
updated when you operate that controller
(DIRECT) or only after the controller reaches
the same position as the parameter’s current
value (CATCH).
Aft Sens 0–100 Specifies the sensitivity of aftertouch.
BUTTON Func
Source SCENE, SYS
Specifies whether the functions assigned
to these buttons follows the settings of the
currently selected scene (SCENE) or the system
settings (SYS).
S1 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S1
button.
S1 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
S2 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S2
button.
S2 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
S3 Func
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the S3
button.
S3 Mode
LATCH,
MOMENTARY
Specifies how the button operates.
SLIDER Func
SL1 Source SCENE, SYS
Specifies whether the function assigned to the
SL1 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
SL1
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the SL1
slider.
SL2 Source SCENE, SYS
Specifies whether the function assigned to the
SL2 slider follows the setting of the currently
selected scene (SCENE) or the system setting
(SYS).
SL2
PEDAL Func
Hold Source SCENE, SYS
Specifies whether the function assigned to the
pedal connected to the HOLD jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Hold
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the pedal
connected to the HOLD jack.
Hold Pole
STANDARD,
REVERSE
Specifies the polarity of the pedal connected
to the HOLD jack.
Ctrl Source SCENE, SYS
Specifies whether the function assigned to the
pedal connected to the CTRL jack follows the
setting of the currently selected scene (SCENE)
or the system setting (SYS).
Ctrl
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the pedal
connected to the CTRL jack.
WHEEL Func
Wheel1 Source SCENE, SYS
Specifies whether the function assigned to
the Wheel1 wheel follows the setting of the
currently selected scene (SCENE) or the system
setting (SYS).
Wheel1
For the values, refer
to Assignable Sheet.
Specifies the function assigned to the Wheel1
wheel.
Wheel2 Source SCENE, SYS
Specifies whether the function assigned to
the Wheel2 wheel follows the setting of the
currently selected scene (SCENE) or the system
setting (SYS).
Parameter
[1] knob
Value
[2] knob
Explanation
Device ID 17–32
When transmitting and receiving system
exclusive messages, the device ID numbers of
both devices must match.
Tone CC Map OFF, ON
Sets whether control change messages (CC) for
the tone parameters are transmitted/received
(ON) or not (OFF).
MIDI Tx
Tx PC OFF, ON
Specifies whether program change messages
will be transmitted (ON) or not be transmitted
(OFF).
Tx Bank OFF, ON
Specifies whether bank select messages will be
transmitted (ON) or not be transmitted (OFF).
Tx Edit OFF, ON
Specify whether changes you make in the
settings of a program will be transmitted as
system exclusive messages (ON), or will not be
transmitted (OFF).
MIDI Rx
Rx PC OFF, ON
Specifies whether program change messages
will be received (ON) or not be received (OFF).
Rx Bank OFF, ON
Specifies whether bank select messages will be
received (ON) or not be received (OFF).
Rx Exclusive OFF, ON
Specifies whether system exclusive messages
will be received (ON) or not be received (OFF).
MIC IN
Mic In Gain -24.0–+24.0 [dB] Adjusts the input level of the MIC IN jack.
Mic Power 0–1
If this is “ON,” plug-in power (5 V) is supplied to
the MIC IN jack.
NS Switch OFF, ON
Switches the noise suppressor on/off.
The noise suppressor is a function that
suppresses noise during periods of silence.
NS Threshold 0–127
Adjusts the volume at which noise suppression
starts to be applied.
NS Release 0–127
Adjusts the time from when noise suppression
starts until the volume reaches 0.
CompSwitch OFF, ON
Specifies whether the mic compressor (a
compressor applied to the mic input) is used
(ON) or not used (OFF).
CompAttack
0.1, 1, 2,... 100
[ms]
Specifies the time from when the input to the
mic compressor exceeds the Comp Thres level
until the volume is compressed.
CompRelease
10, 10, … 1000
[ms]
Specifies the time from when the input to the
mic compressor falls below the Comp Thres
level until compression is no longer applied.
CompThreshold -60–0 [dB]
Specifies the level at which the mic compressor
starts applying compression.
CompRatio
1: 1, 2: 1, …4: 1,
8: 1, 16: 1, 32: 1,
INF: 1
Specifies the compression ratio for the mic
compressor.
CompKnee 0–30 [dB]
Smooths the transition until the mic
compressor starts to be applied.
Higher values produce a smoother transition.
CompOutGain
-24.0, -23.5, … 0,
…, +24.0 [dB]
Specifies the output volume of the mic
compressor.
Rev Send Lev 0–127
Specifies the amount of reverb that is applied
to the mic input.
Cho Send Lev 0–127
Specifies the amount of chorus that is applied
to the mic input.
Dly Send Lev 0–127
Specifies the amount of delay that is applied to
the mic input.
Mic Thru OFF, ON
If you want the mic to be cut when the vocoder
is off, turn this “OFF.”
CONTROLLER
Velocity REAL, 1–127
Specifies the velocity value that is transmitted
when you play the keyboard.
Velo Crv
LIGHT, MEDIUM,
HEAVY
Specifies the keyboard touch.
Velo Offset -10–+9 Adjusts the keyboard velocity curve.