Document Outline

• Contents
• Preface
  • Document conventions
    • Text formatting conventions
    • Command syntax conventions
    • Notes, cautions, and warnings
  • Brocade resources
  • Getting technical help
  • Document feedback
• About This Document
  • Introduction
    • Supported software
  • What’s new in this document
• ICX 6610 Overview
  • Hardware features
  • Management interfaces
    • Console management interface
    • Out-of-band management interface
    • Reset button
  • Network interfaces for ICX 6610devices
    • Slot locations
    • Slot designations
    • 10/100/1000 BASE-T ports
    • SFP interfaces
    • 40-Gbps QSFP interface stacking ports
  • Specifying a port address
    • Specifying a data port
    • Specifying a stacking port
    • Specifying a management port
  • Port, system, and power status LEDs
  • Fan trays
  • Power supplies
    • PoE and PoE+ power
• Installing the ICX 6610 Switch
  • Unpacking the device
    • Package contents
    • General requirements
  • Installation tasks
  • Installation precautions
    • General precautions
    • Lifting precautions
    • Power precautions
  • Preparing the installation site
    • Cabling infrastructure
    • Installation location
  • Installing the device
    • Desktop installation
    • Rack mount installation
    • 2-Post rack mount installation
    • 4-Post rack mount installation
  • Connecting devices in a traditional stack
    • Stacking ports and trunks
      • Trunking requirements
    • Stacking configuration requirements
    • Stacking cables
    • Stack size
    • Stacking topologies
  • Connecting devices in a mixed stack
    • ICX 6610 stacking ports and trunks
      • Ports used to connect ICX 6610 devices in the backbone
      • Trunking requirements
      • Ports used to connect ICX 6610 devices to ICX 6450 devices
    • ICX 6450 stacking ports and trunks
      • Trunking requirements
    • Stacking configuration requirements
      • All configuration methods
      • Secure Setup utility
      • Automatic and manual configuration methods
    • Stacking cables
    • Stack size
    • Stacking topologies
      • Topology 1: Single ring
      • Topology 2: Dual ring
      • Topology 3: Linear and ring
      • Topology 4: Ring with one backbone device
      • Topology recommendations
    • Connecting ICX 6610 devices in the backbone
    • Connecting a peripheral device to an ICX 6610 and to another peripheral device
    • Extended distance stacking
  • Attaching a PC or terminal
  • Powering on the system
  • Power supplies for the Brocade ICX 6610
    • Installing and replacing a power supply unit
    • Installing an AC power supply
    • Installing a DC power supply
    • DC-DC power source cautions
  • Installing or replacing fan trays
• Checking Network Devices and Testing Connectivity
  • Assigning permanent passwords
    • Setting passwords
    • Recovering from a lost password
  • Configuring IP addresses
    • Devices running Layer 2 software
    • Devices running Layer 3 software
      • Configuring IP parameters for devices running Layer 3 software
      • Deleting an IP address
  • Connecting network devices
    • Connectors
    • Cable specifications
    • Connecting to Ethernet or fast Ethernet hubs
    • Connecting to workstations, servers, or routers
      • Automatic MDI or MDIX detection
    • Connecting a network device to a fiber port
      • Fiber Optic transceivers
      • Installing a transceiver
      • Cabling a fiber optic transceiver
      • Cleaning the fiber optic connectors
  • Testing connectivity
    • Pinging an IP address
    • Observing LEDs
    • Tracing a route
  • Troubleshooting network connections
    • Digital optical monitoring
• Managing the ICX 6610 Hardware
  • Managing temperature settings
    • Using the temperature sensor
    • Displaying the temperature
    • Displaying Syslog messages for temperature
    • Changing the temperature warning level
    • Changing the temperature poll time
  • Removing MAC address entries
  • Displaying ICX 6610 CPU usage
  • Hardware maintenance schedule
  • Replacing a copper or fiber optic module
    • Removing a copper or fiber-optic module
    • Cabling a fiber optic module
    • Cleaning the fiber optic connectors
• Hardware Specifications
  • Hardware specifications
    • Physical dimensions and weight
    • Environmental considerations
      • Operating Environment
      • Storage environment
    • Cooling system and fans
    • Pinouts and signalling
      • Console (serial RJ45) management port pinouts
    • Cable specifications
    • Power cords
    • AC power supply specifications
    • Power consumption specifications
• Troubleshooting
  • Diagnosing switch indicators
    • Power and cooling problems
    • Installation
    • In-band access
• Regulatory Statements
  • USA (FCC CFR 47 Part 15 Warning)
  • Industry Canada statement
  • Europe and Australia (CISPR 22 Class A Warning)
  • Germany (Noise Warning)
  • Japan (VCCI)
  • Japan power cord
  • Korea
  • China
  • Russia
  • BSMI statement (Taiwan)
  • Regulatory compliance
• Cautions and Danger Notices
  • Cautions
  • Danger notices
• Index