Document Outline

• Sun™ StorEdge™ FC-100 Hub Installation and Service Manual
  • Formerly the Sun™ Enterprise Network Array™
  • Regulatory Compliance Statements
    • FCC Class A Notice
    • FCC Class B Notice
    • DOC Class A Notice - Avis DOC, Classe A
    • DOC Class B Notice - Avis DOC, Classe B
• Declaration of Conformity
  • EMC
    • European Union-EC
  • Safety
  • Supplementary Information
• Contents
  • 1. Product Description11
  • 2. Installation21
  • 3. Service31
  • A. SpecificationsA1
    • Preface
• Using UNIX Commands
• Typographic Conventions
  • TABLEP1 Typographic Conventions
• Shell Prompts
  • TABLEP2 Shell Prompts
• Related Documentation
• Sun Documentation on the Web
• Sun Welcomes Your Comments
  • 1
  • Product Description
• 1.1 Sun StorEdge FC100 Hub
  • FIGURE11 Front of Hub
  • FIGURE12 Rear of Hub
• 1.2 GBIC
  • FIGURE13 GBIC That Does Not Have a Bail
  • FIGURE14 GBIC That Has a Bail
  • 2
  • Installation
• 2.1 Inspecting the Hub
  • 1. Unpack the hub.
  • 2. Inspect the hub for evidence of damage.
  • 3. Save the packing materials for future use.
• 2.2 Rackmount Placement
• 2.3 Installing the Hub
  • 2.3.1 Tools You Will Need
  • 2.3.2 Preparing the Cabinet
  • 2.3.3 Installing the Mounting Tray in the Cabinet
    • 1. Select the correct mounting holes in the cabinet to use for the tray.
    • 2. Install the tray in the cabinet (FIGURE21).
      • FIGURE21 Installing the Tray in the Cabinet
      • a. In the front of the tray, use the Phillips screwdriver to loosely install two 10-32 screws eac...
      • b. In the back of the tray, use the Phillips screwdriver to loosely install two 10-32 screws each...
      • c. Tighten both sets of screws.
  • 2.3.4 Installing the Hub on the Mounting Tray
    • 1. Determine on which side of the tray you are going to install the hub.
    • 2. From the rear of the tray, slide the hub mounting bracket into the slots in the mounting tray ...
      • FIGURE22 Installing the Hub on a Mounting Tray
  • 2.3.5 Installing GBICs and Fiber Optic Cables
    • 1. Choose the hub port into which you will install the GBIC.
    • 2. Insert the GBIC into the port.
      • FIGURE23 Installing a GBIC and Fiber Optic Cable
      • FIGURE24 Installing a GBIC That Has a Bail and Fiber Optic Cable
    • 3. Connect the fiber optic cable to the GBIC.
    • 4. Route the fiber optic cable to an initiator or target.
    • 5. Connect the fiber optic cable to a GBIC in the initiator or target.
  • 2.3.6 Routing the Power Cord
    • 1. Connect the female end of the power cord to the power receptacle at the rear of the hub (FIGUR...
    • 2. Route the power cord down the right side and along the bottom of the cabinet.
    • 3. Route the power cord up through the cutout to the power distribution unit at the left side of ...
    • 4. Connect the power cord for the tray to the power distribution unit.
    • 5. Tuck the extra length of the power cord down into the pocket beneath the power distribution unit.
  • 2.3.7 Verifying the Configuration
    • 1. Power on all nodes and then the hub.
    • 2. Make sure that the Device Active LEDs are lit for active hub ports.
  • 2.3.8 Reassembling the Cabinet
• 2.4 Troubleshooting
  • TABLE21 Troubleshooting
  • 3
  • Service
• 3.1 Installing a GBIC
  • 1. Choose the hub port into which you will install the GBIC.
  • 2. Insert the GBIC into the port.
    • FIGURE31 Installing a GBIC That Does Not Have a Bail
    • FIGURE32 Installing a GBIC That Has a Bail
  • 3. Connect the fiber optic cable to the GBIC.
• 3.2 Removing a GBIC
  • 1. Disconnect the fiber optic cable from the GBIC (FIGURE33 or FIGURE34).
  • 2. Remove the GBIC.
    • FIGURE33 Removing a GBIC That Does Not Have a Bail
    • FIGURE34 Removing a GBIC That Has a Bail
• 3.3 Removing a Hub
  • 1. Disconnect and remove any installed fiber optic cables or GBICs (FIGURE33).
  • 2. Disconnect the AC power cord from the hub.
  • 3. Push up on the retaining tab that secures the hub to the mounting tray (FIGURE35).
    • FIGURE35 Removing the Hub
  • 4. Pull the hub back and then lift it out of the mounting slots.
  • A
  • Specifications
• A.1 Physical
  • TABLEA1 Physical Specifications
• A.2 Electrical
  • TABLEA2 Electrical Specifications
• A.3 Environmental
  • TABLEA3 Environmental Specifications