Appendix, Menu tree, Ap-1 – Furuno FA-150 User Manual
Page 60
AP-1
APPENDIX
Menu Tree
MODE (
STANDARD
, MONITOR, SERVICE, DISABLE)
IP ADDRESS (000.000.000.000 - 255.255.255.255;
172.031.024.001
)
SUB NET MASK (000.000.000.000 - 255.255.255.255;
255.255.000.000
)
PORT NO. (0 - 65535;
10000
)
IP ADDRESS (000.000.000.000 - 255.255.255.255;
172.031.024.001
)
SUB NET MASK (000.000.000.000 - 255.255.255.255;
255.255.000.000
)
NAVNET PORT NO. (10000 - 30000;
10000
)
GATEWAY ADDRESS (
000.000.000.000
255.255.255.255)
HOSTNAME (
AIS0
AIS9)
AIS OUTPUT (AUTO,
CONTINUOUS
)
GPS OUTPUT (
AUTO
, CONTINUOUS)
ZDA OUTPUT (
AUTO
, CONTINOUES)
[MENU] key
CREATE MSG
TX LOG
RX LOG
SET MSG TYPE
SET MSG
SEND MSG
ADRS TYPE (
BROAD CAST
, ADRS CAST)
MMSI
MSG TYPE (NORMAL,
SAFETY
)
CHANNEL (
ALTERNATE
, BOTH A & B, A, B)
MSG
SENSOR STATUS (Display sensor status.)
INTERNAL GPS (Displays data about internal GPS receiver.)
CPA (0.0 - 6.00,
6.0
(nm))
TCPA (0 - 60,
60
(min))
ALARM MODE (
ON
, OFF)
ALARM BUZZER (
ON
, OFF)
KEY BEEP (
ON
, OFF)
ALARM BUZZER (
ON
, OFF)
DISP RCVD MSG (
ALL
, ABM, OFF)
RCVD MSG BUZZ (
ON
, OFF)
LR MODE (
AUTO
, MANUAL)
AUTO SORT (
ON
,OFF)
CPA/TCPA ALARM
(Continued on
next page)
USER SETTINGS
INITIAL
SETTINGS
SET INT ANT POS.
A (
0
-511 (m))
B (
0
-511 (m))
C (
0
-63 (m))
D (
0
-63 (m))
SET MMSI (MMSI, IMO NO., NAME, C. SIGN)
SET EXT ANT POS.
SET SHIP TYPE (Type no.)
A (
0
-511 (m))
B (
0
-511 (m))
C (
0
-63 (m))
D (
0
-63 (m))
Note: The INITIAL SETTINGS sub menu
shown here is the one accessed with a
password, which permits changing of
settings. If accessed without a password,
in which case "SET" in a menu title is
replaced with "VIEW" and settings cannot
be changed.
SET I/O SET
COM
PORT
SET PC
PORT
SET LAN
PORT*
MODE (
STANDARD
, MONITOR, SERVICE, BEACON, DISABLE)
SPEED (4800BPS, 9600BPS, 19.2KBPS,
38.4KBPS
, 57.6KBPS)
SET COM1
MODE (
LONG RANGE
, EXT DISPLAY, DISABLE)
SPEED (IEC61162-1,
EC61162-2
)
SET COM2
MODE (
EXT DISPLAY
, MONITOR, HI LEVEL IF, DISABLE)
SPEED (
I
IEC61162-1,
EC61162-2
)
SET COM3 (Same as SET COM2.)
SET COM4
MODE (
SENSOR
, EXT DISPLAY, DISABLE)
SPEED (
IEC61162-1
, IEC61162-2)
SET COM5
MODE (SENSOR(Fixed)
SPEED (
IEC61162-1
, IEC61162-2)
SET COM6
MODE (SENSOR(Fixed)
SPEED (I
IEC61162-1
, IEC61162-2, AD-10)
* Shown when
optional LAN kit
is installed.
PORT
*1: For PC Netwark
*2: For NAVNET 3D
(Continued on
next page)
*2
*1