FieldServer FCI 7100 Series - Manual (Page 16)

FS-8700-112 Gamewell-FCI 7100 Driver Manual Page 16 of 20
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262 2299 Fax: (408) 262 2269 Toll Free: (888) 509 1970 email: [email protected]
Message Description
FCI7100:#13a Err. Diagnostic 1); Take a log. Try and repeat the event that
caused the message to be printed. Then
contact tech support.
FCI7100:#13b Err. Diagnostic 2);
FCI7100:#13c Err. Diagnostic 3);
FCI7100:#14 Err. <%s> file not found., md->mapdesc_name ) ;
If this error is repeated often it is possible that
a FCI firmware update as made the driver
unusable. Take a log and contact tech
support.
FCI7100:#15 Err. Event Type=<%s> Not recognized." , drv_bd-
>event_desc )
FCI7100:#16 Err. Point Type='%c'(%#x) Not recognized. ,
drv_bd->point_identifier[0] , drv_bd->point_identifier[0] ) ;
FCI7100:#17 Err. Loop=%d < 1. Rejected. , drv_bd->loop )
This message is printed if a byte in a message
has been corrupted. If you notice it more than
once then take a log and contact tech support.
FCI7100:#18 Err. Loop Type='%c'(%#x) Not recognized. , drv_bd-
>point_identifier[2] , drv_bd->point_identifier[2] )
If this error is repeated often it is possible that
a FCI firmware update as made the driver
unusable. Take a log and contact tech support.
FCI7100:#19 Err. Relay=%d < 1. Rejected. , drv_bd->relay This message is printed if a byte in a message
has been corrupted. If you notice it more than
once then take a log and contact tech support.
FCI7100:#20 Err. Zone=%d < 1. Rejected. , drv_bd->zone"
FCI7100:#21 Err. Point Type not recognized
Valid Point Types are listed in section 5.3.2 3
FCI7100:#22 Err. Undefined Point Type"
FCI7100:#23 Err. Event Type not recognized
Valid Event Types are listed in section
5.3.2Error! Bookmark not defined.
FCI7100:#24 Err. Undefined Event Type
FCI7100:#25a Err. Address+Length>99. Length Truncated
The maximum value for a sensor/module is
99. The combination of address and length
specified produce a number > 99Error!
Bookmark not defined.
FCI7100:#25b Err. Address+Length>99. Length Truncated
FCI7100:#26 Err. Invalid Module number. Expected 1..99
Correct the configuration fileError! Bookmark
not defined. FCI7100:#27a Err. Invalid Loop number. Expected 1..10
FCI7100:#27b Err. Invalid Loop number. Expected 1..10
FCI7100:#27c Err. Invalid Loop number. Expected 1..10
FCI7100:#28 Err. Invalid Sensor number. Expected 1..99
Correct the configuration file. Error!
Bookmark not defined.
FCI7100:#29 Err. Invalid Zone number. Expected 1..255
FCI7100:#30 Err. Invalid Relay number. Expected 1..255
FCI7100:#31 Err. Point Type Invalid.
Valid Point Types are listed in Section
5.3.2Error! Bookmark not defined.
FCI7100:#32 Err. No MD Length. Default to 1
Specify the 'length' of each Map Descriptor.
Refer to Section 5.3.2Error! Bookmark not
defined.
FCI7100:#33 Err. Driver cant poll or write.
The driver can only listen passively for
message from the panel. Remove any active
Map Descriptors from the configuration file.
3 Correct the configuration file, download to the FieldServer and restart the FieldServer for the changes to take effect.