FieldServer NCA2-NFS2-3030 - Manual (Page 20)

FS-8700-130 Notifier NCA2/NFS-3030 Manual Page 20 of 21
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web: www.fieldserver.com
Tel: (408) 262-2299 Fax: (408) 262-2269 Toll Free: (888) 509-1970 email: [email protected]
System Trouble Address System Trouble Address
LOOP CONTINUITY TEST FAIL LOOP 3 231 WALK TEST - FIRE PROTECTION IS LIMITED 485
LOOP CONTINUITY TEST FAIL LOOP 4 232 REMOTE PROG MODE ACCESSED 486
LOOP CONTINUITY TEST FAIL LOOP 5 233 DIA PROG. CHANGE DET. SERVICE REQUIRED 487
LOOP CONTINUITY TEST FAIL LOOP 6 234 ISIB DATA MESSAGE RECEIVED ERROR 488
LOOP CONTINUITY TEST FAIL LOOP 7 235 ISIB EXECUTIVE ROUTINE RE-ENTERED 489
LOOP CONTINUITY TEST FAIL LOOP 8 236 DIB TO SIB CABLE BAD OR MISSING 490
LOOP CONTINUITY TEST FAIL LOOP 9 237 UPLOAD/DOWNLOAD MESSAGE RECEIVED 491
LOOP CONTINUITY TEST FAIL LOOP 10 238 GLOBAL DATABASE MISMATCH 492
AMP FAIL 239 SIB PROG. CHANGE DET. SERVICE REQUIRED 493
AC FAIL 240 HS-NCM SNIFFER MODE ACTIVE 494
SCB ASSEM. COM. VERIFIED FAILED 241 EXCEEDED CONNECTION LIMIT 495
8255 PORT CHIP CONTROL WORD CHECK FAILE 242 NAM CCBE. PROG LOST 496
NETWORK COMMUNICATION LINK FAIL PORT A 243 MEMORY LOSS 497
NETWORK COMMUNICATION LINK FAIL PORT B 244 DVC COMM LOSS 498
STYLE 4 SHORT A L1 245 A.C. POWER LOSS. BACK UP ACTIVATED 499
STYLE 4 SHORT B L1 246 BUZZER OFF-LINE 500
STYLE 4 SHORT A L2 247 PANEL DOOR OPEN 501
STYLE 4 SHORT B L2 248 OFF NETWORK 502
STYLE 4 SHORT A L3 249 INSTALL. ERROR 503
STYLE 4 SHORT B L3 250 OR AUDIO/TELEPHON 504
STYLE 4 SHORT A L4 251 EXPANDER MODULES 505
STYLE 4 SHORT B L4 252 MANUAL CONTROL 506
STYLE 4 SHORT A L5 253 CAT. COMM. FAULT 507
STYLE 4 SHORT B L5 254 UNKNOWN 508
Appendix C.3. Error Messages
Most error messages are associated with errors in parsing an incoming message from the Notifier panel. The most
likely cause is a mismatch in expected message format. The driver will flag one of the following error messages
and continue. In most cases the message currently being processed by the driver will also be printed so that any
problems can be easily diagnosed.
Two screens ‘System Errors’ and ‘Driver Messages’ exist for displaying errors.
The System Error Screen displays the error number and the Driver messages screen displays the error number,
description and the message received from the NCA/NCA2 Panel.
In debug mode the System Error screen will also include Driver messages.
The following Error Messages appear upon the ‘System Errors’ Screen
%d means numeric number
%s means string
Messages number 1, 3, 4 and 5 will be displayed just once if generated after rebooting or power cycling the
FieldServer.
Error Description Action
#1 FYI. Incoming data is
being abandoned on
Port<%d>
Node<%u>
Loop<%d>
Data_Type<%s>
Address<%d>
The FieldServer got a recognized
message on this particular port, Node,
loop, Address_Type and Address but
did not find a defined Map Descriptor.
To capture this data, add a new Map
Descriptor with the required parameters.