Murphy Centurion Configurable Controller CE-05171N User Manual
Page 33
CE-05171N page 33 of 44
Also, the message “History Cleared” will be displayed until another
key is pressed.
d
d)) Reset Fault History
e
e)) Reset Event History
The P1 and P2 signify Communication Port 1 and
Communication Port 2 and are for setting up the RS485 inter-
faces on the display’s serial ports. PU/PD designates the
pull-up and pull-down resistors.
ff)) P1 PU/PD
g
g)) P2 Termination
h
h)) P2 PU/PD
ii)) P2 Termination
New configurations can be downloaded to the display by
selecting the desired connection here. After enabling the
download, download progress is indicated on the left side of
the edit box as a percentage complete. After selecting Yes for
download, and until No is selected after download is com-
plete, only the Enter key will be active. See Section 6.2 for fur-
ther details about downloading configurations.
jj)) Com 1 Config Download
k
k)) Com2 Config Download
ll)) USB Config Download
m
m)) Factory Auto Test: For factory use ONLY.
n
n)) Firmware Download: A firmware update mode screen will
remain until the unit has been reset by remote command or a
power cycle. See Section 7.2.5 for downloading new firmware.
6
6..3
3..1
17
7 C
Co
on
nffiig
gu
urra
attiio
on
n D
Do
ow
wn
nllo
oa
ad
d ((D
Do
ow
wn
nllo
oa
ad
d O
On
nlly
y S
Sc
crre
ee
en
n))
This menu allows for download only and can be accessed
through the Special Jump Code 35. It is the only screen
available by entering the password 35.
a
a) Com 1 Config Download: Selecting Yes initiates configu-
ration download through Communication Port 1.
b
b)) Com2 Config Download: Selecting Yes initiates configu-
ration download through Communication Port 2.
c
c)) USB Config Download: Selecting Yes initiates configura-
tion download through USB port.
d
d)) Firmware Download: Selecting Yes Initiates the download.
6
6..3
3..1
18
8 D
Diis
sp
plla
ay
y B
Bo
oa
arrd
d S
Stta
attu
us
s
The user may view diagnostic information that reflects the
operating conditions of the C3-3 Display only. The Heater
PWM% refers to the LCD heater which only operates in cold
temperature conditions. The reset source indicates the cause
of the last reset. Possible causes for reset include external
reset, power-up, brown-out and watch dog.
a
a)) Battery Volts
b
b)) Board Current
c
c)) Temperature
d
d)) Heater PWM %
e
e)) Reset Source
TM
C
C
C
Super User Menu Screen 3
___________________________________
▼
▼
SUPER USER MENU
COM 1 CONFIG DOWNLOAD
28% YES
COM 2 CONFIG DOWNLOAD
USB CONFIG DOWNLOAD
FACTORY AUTO TEST
FIRMWARE DOWNLOAD
▼▲ ENTER-EDIT
___________________________________
___________________________________
▼
▼
ESC-EXIT THIS MENU
TM
C
C
C
Download Only Screen
___________________________________
▼
▼
CONFIRATION DOWNLOAD
COM 1 CONFIG DOWNLOAD
NO
COM 2 CONFIG DOWNLOAD
USB CONFIG DOWNLOAD
FIRMWARE DOWNLOAD
▼▲ ENTER-EDIT
___________________________________
___________________________________
TM
C
C
C
MView Board Status Screen
___________________________________
▼
▼
▼
▼
MVIEW BOARD STATUS
BATTERY VOLTS
23.3 VDC
BOARD CURRENT
TEMPERATURE
HEATER PWM %
RESET SOURCE
MORE MENUS
___________________________________
___________________________________
TM
C
C
C
Super User Menu Screen 2
___________________________________
▼
▼
SUPER USER MENU
RESET FAULT HISTORY
HISTORY CLEARED NO
RESET EVENT HISTORY
P1 PU/PD
P1 TERMINATION
P2 PU/PD
▼▲ ENTER-EDIT
MORE MENUS
___________________________________
___________________________________
▼
▼