IBM 1220 User Manual
User’s reference
Advertising
Table of contents
Document Outline
- Go back
- Table of contents
- Printer overview
- Understanding the printer operator panel
- Sending a job to print
- Canceling a print job
- Conserving supplies
- Holding a job in the printer
- Paper and specialty media specifications
- Loading the trays
- Loading the multipurpose feeder
- Linking trays
- Linking bins
- Tips for successful printing
- Checking an unresponsive printer
- Understanding jam messages
- Solving print quality problems
- Solving option problems
- Solving mailbox problems
- Solving paper feed problems
- Solving printing problems
- Calling for service
- Configuring printer alerts
- Determining the status of supplies
- Size Sensing
- Ordering supplies and maintenance items
- Aligning the image transfer unit
- Other maintenance and troubleshooting documents
- Clearing image transfer unit jams
- Removing memory and option cards
- Restoring factory default settings
- Disabling the operator panel menus
- Disabling Power Saver
- Changing menu settings
- Printing a menu settings page
- Printing sample fonts
- Understanding printer messages
- Activating Menu Changes
- <x> Alignment
- Bin <x> Full
- Busy
- Calibrating Tray <x>
- Cancelling Fax
- Cancelling Job
- Change <x>
- Change <x> Invalid Refill
- Check <device> Connection
- Clearing Job Accounting Stat
- Close Door
- Close Finisher Door
- Close Tray X Door
- Copying
- Defragmenting
- Delete All Jobs
- Deleting Jobs
- Disabling Menus
- Disk Corrupted. Reformat?
- Disk Recovery x/5 yyy%
- Enabling Menus
- Engine Warming
- Enter PIN: =___
- Fax <x>
- Flushing Buffer
- Formatting Disk
- Formatting Disk yyy%
- Formatting Flash
- Held Jobs may be lost
- Held Jobs May Not Be Restored
- Hole Punch Waste Full
- Incorrect Media
- Infrared <x>
- Insert Staple Cartridge
- Insert Tray <x>
- Install <device> or Cancel Job
- Invalid Engine Code
- Invalid Network <x> Code
- Invalid Standard Network Code
- ITU/Fuser Maint
- Load Manual
- Load <x> Plain Letter
- Load Staples
- Load Tray <x>
- LocalTalk <x>
- Menus Disabled
- Network Card Busy
- Network <x>
- Network <x>, <y>
- No DRAM Installed
- No Jobs Found. Retry?
- Not Ready
- Ovrflow Bin Full
- Parallel <x>
- Performing Self Test
- Power Saver
- Printer Calibrating
- Print Jobs on Disk
- Printing Alignment Page
- Printing Directory List
- Printing Font List
- Printing Job Accounting Stat
- Printing Menu Settings
- Prog Engine Code
- Prog System Code
- Program Flash
- Programming Disk
- Programming Error P<x>
- Queuing and Deleting Jobs
- Queuing Jobs
- Ready
- Ready Hex
- Reattach <device>
- Remove Paper <specified bin>
- Resetting Active Bin
- Resetting Fuser Cnt Value
- Resetting the Printer
- Restore Held Jobs. Go/Stop?
- Restoring Factory Defaults
- Restoring Held Job xxx/yyy
- Restoring Held Jobs
- Serial <x>
- Setup Required
- Staples Low
- Std Bin Full
- Supplies
- Tray <x> Empty
- Tray <x> Low
- Tray <x> Missing
- Tray <x> Not Calibrated
- <type> in <source>. Go?
- USB <x>
- Waiting
- 100–199 Service <message>
- 1565 Emul Error Load Emul Option
- 2<xx> Paper Jam
- 30 ITU Missing
- 30 <color> Toner Cart Missing
- 31 Defective <x> Cartridge
- 32 Unsupported <color> Cartridge
- 33 Calibration Error <x>
- 34 Short Paper
- 35 Res Save Off Deficient Memory
- 37 Insufficient Collation Area
- 37 Insufficient Defrag Memory
- 37 Insufficient Memory
- 38 Memory Full
- 39 Complex Page
- 4<x> Unsupported Firmware Card
- 51 Defective Flash
- 52 Flash Full
- 53 Unformatted Flash
- 54 Serial Option <x> Error
- 54 Standard Serial Error
- 54 Network <x> Software Error
- 54 Std Network Software Error
- 54 Std Par ENA Connection Lost
- 54 Par <x> ENA Connection Lost
- 56 Serial Port <x> Disabled
- 56 Standard Serial Disabled
- 56 Parallel Port <x> Disabled
- 56 Std Parallel Port Disabled
- 56 USB Port <x> Disabled
- 56 Standard USB Port Disabled
- 58 Input Config Error
- 58 Too Many Disks Installed
- 58 Too Many Flash Options
- 59 Incompatible <device>
- 61 Defective Disk
- 62 Disk Full
- 63 Unformatted Disk
- 64 Disk Not Supported
- 64 Unsupported Disk Format
- 80 Fuser Maintenance
- 81 Engine Code CRC Failure
- 82 Waste Bottle Nearly Full
- 82 Waste Toner Bottle Full
- 82 Waste Toner Bottle Missing
- 83 ITU Maintenance
- 84 Oiler Nearly Exhausted
- 84 Replace Oiler
- 87 Fuser Missing
- 88 <color> Toner Low
- 900–999 Service <message>
- Using printer menus
- LocalTalk Menu
- Job Menu
- Infrared Menu
- Finishing Menu
- Color Menu
- Utilities Menu
- USB Menu
- Supplies Menu
- Setup Menu
- Serial Menu
- PostScript Menu
- PCL Emul Menu
- Parallel Menu
- Paper Menu
- Network Menu
- Understanding fonts
- Notices