Integra DTR-10.5 - Manual (Page 68)

68
Enjoying Movies and Music in the Remote Zone (Zone 2/3) —Continued
Operating with the Remote Controller
When operating with the remote controller, how to
operate depends on the location of Zone 2 or Zone 3, or
the distance from the DTR-10.5.
• Point the remote controller at the infrared receiver on
the DTR-10.5, and then operate the controller.
• Install a remote controller sensor in Zone 2 or Zone 3
through an IR connection (See page 48).
• Switch the Transmission Signal Format to RF (Radio
Frequency) (depending on the destination) (See page
141).
Operating on the DTR-10.5
1 Power on the devices in Zone 2 or Zone 3.
Press the [Zone 2] or [Zone 3] button, and then
the [On] button.
2 Select a source.
Rotate the scroll wheel to select a source while
the [Zone 2] or [Zone 3] button is lighted (if the
button is not lighted, press the [Zone2] or [Zone
3] button to light it).
• When you have selected the tuner, you can
choose a preset channel with the [CH Disc
+/–] button.
3 Adjust the volume level.
Press the [Zone 2] (or [Zone 3]) button, and
within 5 seconds, press the [Level –/+] button to
adjust the volume level.
Notes:
• When the pre-main amplifier or receiver is
connected, the volume level should be adjusted
at the connected component side.
• When not using Zone 2 or Zone 3, press the
[Zone 2] (or [Zone 3]) button, and then press
the [Standby] button.
ABC DEF
PQRS TUV WXYZ
GHI JKL MNO
Caps Delete Language Loca t ion
Album Ar tist Genre Playlist
Repeat Video Music Photo
@.-'/
--/--- Direct Tuning #
Custom
Display
Dimmer
T V Input
Sleep
Random Main A Main B
Muting
Angle Subtitle Audio
Memory Search A-B Repeat
On Standby T V
T V CH
T V VOL
RC-556M
Exit Gu ide
Rec
Last Memory
Prev CH
Enter
Set up Retu rn
Test Tone CH SEL
Pure A
Surround
Direct
Stereo
Re-EQ
THX All CH ST
Level + Level -
L Night Audio SEL
DSP DSP
+10 0 Clear
1 2 3
4 5 6
7 8 9
Input
To p M enu Men u
VOL CH
Disc
I
+
-
+
-
Zone 3
Zone 2
Input Mode
Macro
Se rve r Aud io A D J CH Disc +/–
On, Standby
Level –/+
Zone 2
Zone 3
1 Turn on the power supply to the DTR-10.5,
and then select a source for Zone 2 or
Zone 3.
For Zone 2, press the [Zone 2] button, and then
select the source with the [Select/Preset] dial.
For Zone 3, press the [Rec/Zone 3] button, and
then, select the source with the [Control/Tuning]
dial.
When you press the [Zone 2] or [Rec/Zone 3]
button, the [Standby] indicator on the DTR-10.5
blinks for five seconds, so perform operations
while it is blinking.
The source button for Zone 2 lights in green and
the source buttton for Zone 3 lights in red.
To switch the source for Zone 2 (or Zone 3) and
the main room simultaneously:
Repeatedly press the [Zone 2] (or [Rec/Zone 3])
button to display “Z2Sel:SOURCE,” and then
select the source.
2 Adjust the volume level.
For Zone 2, press the [Level] button under the
[Zone 2] button, and then adjust with the [Select/
Preset] dial.
For Zone 3, press the [Level] button under the
[Rec/Zone 3] button, and then adjust with the
[Control/Tuning] dial.
Notes:
• When a pre-main amplifier or receiver is
connected to the DTR-10.5, the volume level
should be adjusted at the connected component
side.
Phones
Listening Mode Audio Selector Tone Zone 2 Select/ Preset
Push To Enter
Setup Control / Tuning
Push To Enter
Rec/ Zone 3 Digital S Video Video Audio L R Video 7 Input
Level Exit Level Dimmer Memory Tuning
Mode
Clear
Pure Audio Open DVD
Display Tape 1 Tape 2 Tuner Phono C D Net Audio
Video 1 Video 2 Video 3 Video 4 Video 5 Video 6 Video 7
Standby
Master Volume
Rec/ Zone 3 Red ) ( Main Blue ( ) Zone 2 Green ( )
Standby/On
Standby/On
Rec/Zone 3 Zone 2
Control/Tuning Select/Preset