JVC RM-P2580 - Manual (Page 17)

17
When an alarm signal is received, this unit performs the following operations.
<Alarm priority mode>
● The video is switched to the camera position from which the alarm signal is received.
● An alarm signal will automatically override and cancel the operation of either AUTO PATROL or AUTO SEQUENCE. (AUTO
SEQUENCE: In A mode only.)
●
The preset alarm title is displayed in the preset size.
● The ALARM indicator blinks and the buzzer sounds. ( REF. : “BUZZER TIME” on page 32 for the setting method.)
● The CAMERA display indicates the number ID of the camera which has given the alarm signal.
● The UNIT ALARM output is turned ON.
<Manual priority mode>
●
When an alarm signal is received during manual operation (except during the AUTO PAN, AUTO PATROL and AUTO SE-
QUENCE operations), the alarm operation does not start.
● When an alarm signal is received from a camera other than the camera being controlled manually, the alarm operation starts
but, unlike in the alarm priority mode, the buzzer does not sound and the camera in question is not automatically selected.
3. APPLIED OPERATIONS
ALARM OPERATION
Alarm input signals can be applied to the DATA I/O terminals on the rear panel. The unit functions in either the
ALARM PRIORITY mode or the MANUAL PRIORITY mode when an alarm signal is input. ( REF. : “CONTROL
UNIT SCREEN” on page 28 and “PRIORITY item of ALARM SCREEN” on page 32.)
Alarm Operation Modes
• In B mode, the MONITOR OUTPUT 2 connector outputs the same video as the MONITOR OUTPUT 1 connector.
For B Mode connection. REF. : [Applied System (B Mode)] on page 21.
B Mode output signal REF. : [B Mode] on page 22.
• While the MENU screen is displayed, the alarm signal is not accepted.
1
TO CAMERA TO CAMERA DATA I / O DATA I / O RX+ RX- TX+ TX- COM COM 1 2 3 4 5 6 7 8 COM COM 9/1 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM COM COM COM COM CAMERA CAMERA SW SW UNIT UNIT ALARM ALARM AUTO AUTO
4 3 1 2 8 7 5 6
2 3 4 5 6 7 8
1
MONITOR MONITOR OUTPUT OUTPUT MONITOR MONITOR
SERIAL-2 SERIAL-2 SERIAL-1 SERIAL-1
VIDEO INPUT VIDEO INPUT
VIDEO OUTPUT
OUTPUT OUTPUT
2
1 ON 2 3 4 5 6 7 8
POWER
OFF ON
AC INPUT `
DATA I/O terminals
Alarm input 2
Alarm input 1
Alarm input 2
Camera 1 alarm time
Camera 2 alarm time
UNIT ALARM
output duration
MONITOR OUTPUT 1
MONITOR OUTPUT 2 CAMERA2 CAMERA3
CAMERA3 CAMERA2 CAMERA3
CAMERA4 CAMERA CAMERA
CAMERA CAMERA
CAMERA4 CAMERA5 CAMERA6 CAMERA7
ALARM TIME
ALARM TIME
Set in item "TIME" in the AUTO SEQUENCE screen.
Time period of switching by CAMERA SW. *Encircled number shows the alarm condition.
Time
Alarm input 1
SETUP
MENU MENU SET
SPEED
IRIS IRIS
AF AF
FOCUS FOCUS
ZOOM ZOOM
OPEN OPEN
FAR
TELE CLEAR /HOME /HOME
7
4
1
8
0
5
2
9
6
3
ENTER
AUTO AUTO
PAN PAN
OPTION OPTION
1
OPTION OPTION
2
CAMERA CAMERA POSI- POSI-
TION
AUTO AUTO
PATROL PATROL
CLOSE
NEAR NEAR
WIDE WIDE
AUTO AUTO F-1 F-2 F-3 F-3
PAN/TILT PAN/TILT LENS LENS CAMERA/POSITION CAMERA/POSITION
CAMERA CAMERA POSITION POSITION
REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 RM-P2580
ALARM
POWER
KEY LOCK
<Example when Alarm 1 and Alarm 2 are input during AUTO SEQUENCE in the A Mode>