JVC RM-P2580 - Manual (Page 6)

6
8 [AUTO] button
When this button is pressed, the unit enters the AUTO SE-
QUENCE mode, in which the indicator lights up and the
MONITOR OUTPUT 1 connector
‚ on the rear panel out-
put the camera video signals according to automatic switch-
ing.
REF. : “AUTO SEQUENCE OPERATION” on page 13.
9 [F1, F2, F3] Function buttons
These buttons are valid only when SW-D7000/SW-D8000
frame switchers are being used.
When this unit is operated in the B mode, these buttons
can control certain functions of the specific frame switcher
model connected to this unit. The RS-232C control is in-
volved in this control operation.
For details, please consult your dealer or JVC-authorized
service agent.
REF. : “APPLIED SYSTEM (B MODE)” on page 22.
F1: Single-screen select switch
Press this button to output a single-screen video from
the frame switcher.
The camera number can be selected using the numeric
keypad, etc.
F2: Split-screen select switch
Press this button to output a split-screen video from
the frame switcher.
F3: LIVE/PLAY switch
Press this button to switch between the playback video
of a time-lapse VCR and the camera video.
0 [CAMERA] button
Press when selecting a camera.
To select a camera, use the following buttons:
CAMERA button
0 →
Numeric key buttons * →
ENTER button & .
REF. : “CAMERA SELECTION” on page 10.
! [POSITION] button
Press when selecting one of the position numbers preset
for the camera.
To select a position, use the following buttons:
POSITION button
! →
Numeric key buttons * →
EN-
TER button & .
REF. : “POSITION SELECTION” on page 11.
@ [OPTION 1, 2]
These buttons are not used for the present. Do not touch
them.
# [PAN/TILT] control lever
Operate the lever to pan (swing horizontally) or tilt (swing
vertically) the rotary turret of a camera.
8 (Up) : Tilt the lever in this direction to tilt the rotary
turret upward.
9 (Down) : Tilt the lever in this direction to tilt the rotary
turret downward.
; (Right) : Tilt the lever in this direction to pan the rotary
turret toward the right.
: (Left) : Tilt the lever in this direction to pan the rotary
turret toward the left.
REF. : “MANUAL OPERATION” on page 12.
While a menu screen is displayed, this lever is used to
select or to set an item.
REF. : “MENU OPERATION METHOD” on page 26.
1. INTRODUCTION
CONTROLS, CONNECTORS AND INDICATORS (Continued)
SETUP SETUP
MENU MENU SET SET
SPEED SPEED
IRIS IRIS
AF AF
FOCUS FOCUS
ZOOM ZOOM
OPEN OPEN
FAR FAR
TELE TELE CLEAR CLEAR
/HOME /HOME
7
4
1
8
0
5
2
9
6
3
ENTER ENTER
AUTO AUTO
PAN PAN
OPTION OPTION
1
OPTION OPTION
2
CAMERA CAMERA POSI- POSI-
TION TION
AUTO AUTO
PATROL PATROL
CLOSE CLOSE
NEAR NEAR
WIDE WIDE
AUTO AUTO F-1 F-1 F-2 F-2 F-3 F-3
PAN/TILT PAN/TILT LENS LENS CAMERA/POSITION
CAMERA CAMERA POSITION POSITION
REMOTE CONTROL UNIT REMOTE CONTROL UNIT RM-P2580 RM-P2580
ALARM ALARM
PO POWER WER
KEY LOCK KEY LOCK
* & (
¤
⁄
)
‹
$ ^ %
9
@
#
0
8
!