Sony XDCAM PDW-1500 - Manual (Page 46)

Chapt
er
4
Re
c
o
rdin
g/
Pla
y
ba
c
k
46
4-1 Recording
extended menu item 626 “TC MODE” to “ext regen”
automatically synchronizes the internal time code
generator to the time code received through the S400
(i.LINK) connector or SDI IN connector.
• When extended menu item 626 “TC MODE” is set to
“ext regen,” the internal time code advance mode and
frame count mode (for 525 line mode only) are
automatically set as follows.
Advance mode: free running
Frame count mode (for 525 line mode only): the same
as the external time code signal (drop frame or non-
drop frame)
To check the synchronization to the external
signal
Press the STOP button to stop this unit, then press the REC
button.
Check that the time code value shown in the time data
display coincides with the external time code value.
To record external time code directly
You can record both of the following types of external time
code directly.
• TC input to the TIME CODE IN connector of this unit
• i.LINK TC input to the S400 (i.LINK) connector of
this unit
When you use this method, the internal time code
generator advances without being affected by the external
time code.
To record the playback time code of external VTRs, the
methods described above in “To record with the internal
time code generator synchronized to external time code”
are recommended.
Use the following procedure to record external time code
directly, according to the type of external time code.
1
Make either of the following connections and settings.
To directly record TC input to the TIME CODE IN
connector
Connect the time code output from the external device
to the TIME CODE IN connector. Press the VIDEO
INPUT SEL button and, while viewing the INPUT
display, select one of SDI, CMPST, or SG.
To directly record i.LINK TC
Connect an i.LINK signal to the S400 (i.LINK)
connector. Press the VIDEO INPUT SEL button and,
while viewing the INPUT display, select i.LINK.
2
Press the MENU button and set extended menu item
626 “TC MODE” to “ext preset.”
For details of menu setting operations, see Chapter 8
“Menus” (page 91).
4-1-3 Recording Operation
To record, proceed as follows.
1
Insert a disc.
For details, see 3-5-4 “Loading and Unloading a
Disc” on page 38.
2
Hold down the REC button, and press the PLAY
button.
Recording starts.
3
To stop recording, press the STOP button.
If the disc becomes full
Recording stops and the message “ALARM DISC END.”
appears on the monitor.
REC
VARIABLE
PRESET
PB
L MIX
R
MONITOR
NETWORK LOCAL REMOTE
ACCESS
PHONES
TOP F REV F FWD END
PREV NEXT PLAY
AUDIO MONITOR SEL METER SEL INPUT CH INPUT SEL VIDEO INPUT SEL COUNTER SELECT
SUB CLIP THUMB NAIL SET RESET
SHIFT
EJECT
HOLD
STOP REC
SH UTT LE JOG VAR
MARK1 ESSENCE MARK CLIP MENU S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER dB
-12 -20
-30 -40 -60
0
CH- 15
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 26
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 37
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 48
SG DATA
ANA SDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU VITC VITC COUNTER REC INH VIUB
EDIT KEY INH REMOTE [9P iLINK] INPUT i.LINK
SDI
1/2 5/6 3/4 7/8 625 525 IMX[50 40 30] DVCAM 4 8 CH 18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR AUDIO
SYS MENU MENU
1 2
REC
VARIABLE
PRESET PB
L MIX
R
MONITOR
NETWORK LOCAL REMOTE
ACCESS
PHONES
TOP F REV F FWD END
PREV NEXT PLAY
AUDIO MONITOR SEL METER SEL INPUT CH INPUT SEL VIDEO INPUT SEL COUNTER SELECT
SUB CLIP THUMB NAIL SET RESET
SHIFT
EJECT
HOLD
STOP REC
SH UTT LE JOG VAR
MARK1 ESSENCE MARK CLIP MENU S.SEL
MARK2
IN OUT
ALL/CH-1 CH-2 CH-3 CH-4
OVER dB
-12 -20
-30 -40 -60
0
CH- 15
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 26
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 37
SG DATA
ANA SDI
AE8/EBU
OVER dB
-12 -20
-30 -40 -60
0
CH- 48
SG DATA
ANA SDI
HOURS MINUTES SECONDS FRAMES
AE8/EBU VITC VITC COUNTER REC INH VIUB
EDIT KEY INH REMOTE [9P iLINK] INPUT i.LINK
SDI
1/2 5/6 3/4 7/8 625 525 IMX[50 40 30] DVCAM 4 8 CH 18 24 BIT
CMPST
Y-R,B
SG
ALARM
MONITOR AUDIO
SYS MENU MENU
2 3
1