Sony STR-DA4ES - Manual (Page 79)

Additional Information
79 GB
Remote control RM-US105A
(STR-DA7ES only)
Remote control system
Infrared control
Power requirements 3 V DC with two R6
(size-AA) batteries
Dimensions 210
Ч
45
Ч
25 mm
Mass (approx.) 95 g excluding batteries
General
Power requirements 120 V AC, 60 Hz
Power consumption
Models of area code U
STR-DA7ES:
450 W
STR-DA4ES: 420 W
Models of area code CA
STR-DA7ES:
490 VA
STR-DA4ES: 470 VA
Power consumption (during standby mode)
1 W
AC outlets 2 switched, 120 W/1A
Dimensions 430
Ч
174
Ч
465 mm
including projecting parts
and controls
Mass (Approx.)
STR-DA7ES: 21.0 kg
STR-DA4ES: 21.0 kg
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Audio/video/control S cord (1)
Control S cord (mini jack) (1)
STR-DA7ES only;
Remote commander RM-TP1 (1)
Battery charger (1 for RM-TP1)
AC adapter (1 for RM-TP1)
Remote commander RM-US105A (1)
R6 (size-AA) batteries (2)
STR-DA4ES only;
Remote commander RM-LP211 (1)
LR6 (size-AA) batteries (3)
For details on the area code of the component you
are using, see page 3.
Design and specifications are subject to change
without notice.
FM tuner section
Tuning range 87.5 - 108.0 MHz
Antenna terminals 75 ohms, unbalanced
Sensitivity
Mono: 18.3 dBf, 2.2 µV/75 ohms
Stereo: 38.3 dBf, 22.5 µV/75 ohms
Usable sensitivity 11.2 dBf, 1 µV/75 ohms
S/N
Mono: 76 dB
Stereo: 70 dB
Harmonic distortion at 1 kHz
Mono: 0.3%
Stereo: 0.5%
Separation 45 dB at 1 kHz
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
Selectivity 60 dB at 400 kHz
AM tuner section
Tuning range
With 10-kHz tuning scale: 530 – 1710 kHz 4)
With 9-kHz tuning scale: 531 – 1710 kHz 4)
Antenna Loop antenna
Usable sensitivity 50 dB/m (at 1,000 kHz or
999 kHz)
S/N 54 dB (at 50 mV/m)
Harmonic distortion 0.5 % (50 mV/m,
400 Hz)
Selectivity
At 9 kHz: 35 dB
At 10 kHz: 40 dB
4) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down TUNING + and press
?/1. All preset stations will be erased when you
change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
Video section
Inputs/Outputs
Video: 1 Vp-p, 75 ohms
S-video: Y: 1 Vp-p, 75 ohms
C: 0.286 Vp-p, 75 ohms
COMPONENT VIDEO: Y: 1 Vp-p, 75 ohms
B-Y: 0.7 Vp-p, 75 ohms
R-Y: 0.7 Vp-p, 75 ohms