Samson Txm16 - Manual (Page 19)

- 10dBV.
TRS phone jack connector pin-out - Sleeve: Ground, Tip:
Hot (+), Ring: Cold (-)
CD/TAPE IN and RECORD OUT
You can interface a cassette recorder, computer sound
card or other recorders using the TXM16 and TXM20’s CD/
TAPE and RECORD OUT.
G - CD/TAPE Inputs - RCA jacks
The TXM mixers feature a stereo line level input, on RCA
connectors, for connecting the output of devices such
as MP3, CD, computer soundcard, cassette player, or any
other line level device.
H - Record Out - RCA jacks
The signal present at this connector is the MAIN bus sig-
nal before it has passed through the MASTER level control
and graphic equalizer. The nominal output level is -10dBV
and the impedance is 100 Ohms.
Master Input and Output Section
The TXM mixer's Master Input and Output section has the
connectors for interfacing the PHONES, FOOTSWITCH,
MAIN OUT, MAIN OUT 2, MAIN INSERT POINTS, AMP IN,
and the master AUX OUT’s.
I – FOOTSWITCH - 1/4-inch jack
With a footswitch connected to this jack, you can turn on
and off the on-board digital effects by simply stepping on
the footswitch.
J- EFX OUT- 1/4-inch jack
The EFX OUT (AUX 3) output is used to send a signal to an
external signal processor such as a delay or reverb. The
signal present at the AUX 3 output is sent from the AUX3/
DSP bus, which is fed from the AUX3/DSP send on the
input channels. TR phone jack connector pin-out - Sleeve:
Ground, Tip: Hot (+), Ring: Cold (-).
K- AMP IN (Left and Right) - 1/4-inch jacks
The Left and Right AMP IN 1/4-inch phone jacks are used
to make a direct connection to the TXM’s internal power
amplifiers. You can connect a stereo source like the out-
put from an external mixer here. TR phone jack connector
pin-out - Sleeve: Ground, Tip: Hot (+).
L - MAIN INSERT (Left and Right) - 1/4-inch Send
and Return jack
Send and return patch point on TRS (TIP/RING/SLEEVE)
jack for interfacing external effects processors on Left and
Right MIX bus. The signal is sent on the tip (the Send) and
returns (the Return) on the sleeve of the connector.
M – PHONES - 1/4-inch jack
Connect standard stereo headphone, 60 to 600 Ohms,
here.
N - MONO/SUB OUT- 1/4-inch jack
The Left and Right Mix outputs are summed together and
sent to the MONO/SUB output. The volume of the Mono
signal can be adjusted using the MONO/SUB OUT level
fader control and used to feed a speaker zone in a fixed
installation. For added flexibility, the MONO/SUB OUT can
be used to a feed a subwoofer using the onboard variable
Low Pass Filter. TR phone jack connector pin-out - Sleeve:
Ground, Tip: Hot (+).
O - AUX OUT (1 and 2) - 1/4-inch jacks
The signal present at the AUX 1and Aux 2 outputs are sent
from the AUX 1 and AUX 2 bus, which is fed from the AUX
1 and AUX 2 control knobs on the input channels. The
AUX 1 and AUX 2 are normally used as a MONITOR MIX
bus in a live sound situation by connecting the output to
a power amp and monitor speaker. TR phone jack connec-
tor pin-out - Sleeve: Ground, Tip: Hot (+).
P - MAIN OUT - 1/4-inch jacks
In a live sound application, you can drive a second speak-
er system using MAIN OUT outputs connected to a power
amplifier or powered speakers. The signal at the MAIN
OUT jacks follows the MAIN volume fader. TR phone jack
connector pin-out - Sleeve: Ground, Tip: Hot (+).
Q - MAIN OUT 2- 1/4-inch jacks
In a live sound application, you can drive a second
speaker system using the MAIN OUT 2 outputs connected
to a power amplifier or powered speakers. In a recording
application, the MAIN OUT 2 outputs are used to connect
a stereo device such as computer sound card, MP3, or cas-
sette recorder. The signal at the MAIN OUT jacks follows
the MAIN OUT 2 level control knob allowing you to set a
different level to the recorder. TR phone jack connector
pin-out - Sleeve: Ground, Tip: Hot (+).
( )
+ 0 1 2
/
. - ,
*
TXM16 and TXM20 Input and Output Connections
ENGLISH
15