Kyocera FS1750 User Manual
Page 124
*1: Depending on the emulation selected, the following set
!&RGHýVHWV are available.
*2: The printer can be set to print error data during KPDL emula-
tion. If this is set to
ý2Q, error data will be printed if trouble
occurs during printing. This is set to
ý2II before leaving the
factory.
*3: You can select either Courier or Letter Gothic. Any font can
be selected as
ý'DUN orý5HJXODU. These fonts are dis-
played when the Font menu is Internal.
*4: The
ý!6L]H menu is not available for the Courier and Let-
ter-Gothic fonts. The
ý!3LWFK menu is displayed instead
for these fixed width fonts.
*5: Although
ý$XWR is the default setting and this menu does
not usually appear, page protection mode will be forcibly set
to on if a
ý3ULQWýRYHUUXQý3UHVVý&217,18(
error occurs due to insufficient printer memory. Be sure to
return this setting to
ý$XWR in order to maintain high printer
memory efficiency.
*6: Turning this to
ý21 increases the maximum number of char-
acters that can be printed in a line for an A4 page (78 char-
acters at 10 pitch) and likewise increases the maximum per
line on Letter size paper (80 characters at 10 pitch).(Only PCL
6 emulation)
*7: This sets the resolution for printing. For 1200 dpi there are
two modes. In Fast 1200 mode, printing is equal to 1200 dpi
(1200 dpi horizontal × 600 dpi vertical) comparatively, Fine
1200 mode is slower, but in Fine 1200 mode true1200 dpi
printing is facilitated. The printing is slower than Fast mode
but the print quality is better.
*8: This is displayed only after the FS-1750 memory has been
expanded. (The total must be 12 MB or more)
*9: This is displayed when the size dial on the paper cassette is
set to Custom. (See section 2.7. Setting Custom Sizes.)
*10:This sets whether to enable or disable the difference between
A4 size and letter size. Under the default setting of
ý2II, the
paper size of the paper source is matched to the paper size
given for the data, and if these differ a corresponding error
message is displayed. When this is set to
ý2Q, printing is per-
formed even if the actual paper size differs from the paper
size given for the data.
*11:This menu is displayed only when
ý&XVWRPýú is selected.
*12:After the printer accepts all data and there is no more data
from the computer, the printer will wait a set amount of time
without printing the final page. Once this preset amount of
time has elapsed, the printer will automatically issue a form
feed. This timeout setting can be set in 5-second increments
up to 495 seconds.
*13:This is the total number of pages printed by the printer up to
the present time.
*14:These menus are for service personnel.
They should not be operated by the user.
ý
!5HVRXUFHý SURWï
э э 3HUPý îý 7HPS
ý
Continued from Previous page
ý
2WKHUVý э э э э э э э э э э !
э
!)RUPý )HHG
ý 7LPHý 2XWэ нкнэ VHFï
э
!06*э ODQJXDJH
э э (QJOLVK
(*12)
ý
!6OHHSý WLPHU
э э э э э э э э э э нкнэ PLQï
ý
!3ULQWý +(;р'803
э
!3ULQWHUý 5HVHW
ý
!1XPEHUý RIý SDJHV
ý SULQWHGý нмлкйиз
э
!5HVRXUFHý SURWï
э э 3HUPDQHQW
ý
!5HVRXUFHý SURWï
э э 2II
ý
!%X]]HU
э э 2II
ý
!%X]]HU
э э 2Q
ý
!6HUYLFHý э э э э э э э э !
э
!!'HYHORSHU
ý
!!3ULQW
ý 6WDWXVý 3DJH
ý
!!'UXP
(*14)
(*13)