St. vintage wah (stereo vintage/custom wah), Effects, Advanced – KORG Professional Engineer PA3 User Manual

Page 115: Eq and filters (eq/filter), A: frequency bottom a: frequency top, B: sweep mode, C: envelope sens, C: envelope shape, D: lfo frequency [hz] e: midi sync, A: shape

Advertising
background image

113

Effects

EQ and Filters (EQ/Filter)

Advanced

a: Frequency Bottom
a: Frequency Top

The sweep width and direction of the wah filter are determined
by the “Frequency Top” and “Frequency Bottom” settings.

b: Sweep Mode

This parameter changes the wah control mode. Setting “Sweep
Mode” to Auto will select an auto-wah that sweeps according to
envelope changes in the input signal level. Auto-wah is fre-
quently used for funk guitar parts and clav sounds.

When “Sweep Mode” is set to D-mod, you can control the filter
directly via the modulation source in the same way as a wah
pedal.

When “Sweep Mode” is set to LFO, the effect uses LFO to sweep
in cycle.

c: Envelope Sens

This parameter sets the sensitivity of auto-wah. Increase the
value if the input signal is too low to sweep. Reduce the value if
the input signal is so high that the filter is stopped temporarily.

c: Envelope Shape

This parameter determines the sweep curve for auto-wah.

d: LFO Frequency [Hz]
e: MIDI Sync

When “MIDI/Tempo Sync”=Off, the LFO speed uses the LFO
Frequency parameter setting. When “MIDI/Tempo Sync”=On,
the LFO speed follows the “BPM”, “Base Note”, and “Times” set-
tings.

e: BPM
e: Base Note
e: Times

One cycle of LFO sweep is obtained by multiplying the length of
a note (r…w) (selected for “Base Note”, in relation to the tempo
specified in “BPM”, or the MIDI Clock tempo if “BPM” is set to
MIDI) by the number specified in the Times parameter.

12: St. Vintage Wah

(Stereo Vintage/Custom Wah)

This effect simulates the tonal character of a vintage wah pedal.
You can customize the tone and range settings.

a: Shape

This parameter specifies the sweep curve of the wah. It applies to
all control via auto-wah, modulation source, and LFO, and lets
you adjust subtle nuances of the wah effect.

Max

D

-mod

Frequency

Bottom=25

Top=75

Higher

Max

Zero

Higher

D

-mod

Frequency

Bottom=60

Top=30

Higher

Zero

Higher

Frequency

Bottom=25

Top=75

Higher

Frequency

Bottom=75

Top=25

Higher

Sweep Mode=Auto

Envelope

Envelope

Time

Wah

Woo

Woo

Woo

Envelope

Wah

Wah

Time

Woo

Woo

Wah

Wah

Sweep Mode=D-mod

Time

Level

Envelope

value = 0...–100

value = 0...+100

Envelope Shape

a

Mode

Preset, Custom

Selects either preset or custom
settings

Shape

–100...+100

Sets the curve of the sweep

Invert

Off, On

Inverts the polarity of the sweep

b

Frequency
Bottom

0...100

Sets the lower limit of the wah
center frequency when Mode =
Custom

Frequency Top 0...100

Sets the upper limit of the wah
center frequency when Mode =
Custom

c

Resonance
Bottom

0...100

Sets the lower limit of resonance
amount when Mode=Custom

Resonance Top 0...100

Sets the upper limit of resonance
amount when Mode=Custom

d

Sweep Mode

Auto,
D-mod,
LFO

Selects the control from auto-wah,
modulation source, and LFO

Src

Off...Tempo

Selects the modulation source for
the wah when Sweep Mode=D-mod

Manual

0...100

Sets the center frequency when
Sweep Mode=D-mod and
Source=Off

e

Envelope Sens 0...100

Sets the auto-wah sensitivity

Response

0...100

Sets the speed of response when
Sweep Mode=Auto or D-mod

f

LFO Frequency
[Hz]

0.02...20.00

Sets the speed of the LFO

Src

Off...Tempo

Selects a modulation source for LFO
speed

Amt

–20.00...
+20.00

Sets the modulation amount of LFO
speed

g

MIDI Sync

Off, On

When this is on, the LFO speed is set
by BPM, Base Note, and Times,
instead of Frequency

BPM

MIDI,
40.00...
300.00

MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect

Base Note

r...w

Selects the type of notes that
specify the LFO speed

Times

x1...x32

Sets the number of notes that
specify the LFO speed

h

Output Level

0...100

Sets the output level of the effect
sound

Src

Off...Tempo

Selects the modulation source that
will control the effect output level

Amt

–100...+100

Sets the modulation amount of the
effect output level

i

Wet/Dry

Dry, 1:99...99:1,
Wet

Balance between the wet and dry
signal

Src

Off...Tempo

Table , “Dynamic Modulation
sources,” on page 106

Amt

–100...+100

Amount of modulation source

Mode

Preset Setting

Custom Parameters

Stereo In - Stereo Out

D

-mod

Envelope Sens

Shape / Invert

Response

FX Amt

Wah

Sweep Mode

D-mod

Auto

Left

Right

FX Amt

LFO

LFO

Wah

+

Advertising