KORG Professional Engineer PA3 - Manual (Page 180)

178 Effects
Double Size
136: Hold Delay
This effect records the input signal and plays it back repeatedly.
You can control the start of recording and reset via a modulation
source. Easy to use for real-time performances.
a: Loop Time [msec]
With Auto, the loop time is automatically set. Otherwise, you
can specify the loop time.
When Auto is selected, the Loop Time is automatically set to the
time it takes for a performance recorded while the Modulation
Source or “Manual REC Control” is on. However, if the time
length exceeds 10,800msec, the loop time will be automatically
set to 10,800msec.
c: Time Over?
You can set the delay time up to 10,800msec. If the delay time
exceeds this limit, the error message “OVER!” appears in the dis-
play. Set the delay time parameters so that this message will not
appear. “Time Over?” is only a display parameter.
b: Loop BPM Sync
c: BPM
d: Loop Base Note
d: Times
If “Loop BPM Sync” is on, the “Times” setting is ignored; the
loop time is determined by “BPM,” “Loop Base Note,” and
“Times.” Even in this case, the delay time cannot exceed 10,800
msec.
“Hold” procedure (when Loop Time = Auto)
1. “Rec Src”JS +Y: #01
“Reset Src”JS –Y: #02
“Manual REC Control”REC Off
“Manual RST Control”RESET
“Loop Time [msec]”Auto
“MIDI/Tempo Sync”Off
It should be noted that all recordings will be deleted while
Reset is On.
2. “Manual RST Control”Off
Reset is cancelled and the unit enters Rec ready mode.
3. Push the joystick in the +Y direction (forward) and play a
phrase you wish to hold. When you pull the joystick to its
original position, the recording will be finished and the
phrase you just played will be held.
Loop Time is automatically set only for the first recording
after resetting. If the time length exceeds 10,800msec, Loop
Time will be automatically set to 10,800msec. (If you have
set “Times” to 1–10,800msec, the specified loop time will
be used regardless of the time taken from pushing the joy-
stick forward until it is pulled back. However, the recording
method remains the same. The phrase being played while
the joystick is pushed forward will be held.)
4. If you made a mistake during recording, pull the joystick in
the –Y direction (back) to reset. In this way, the recording
will be erased. Repeat step 4. again.
5. The recorded phrase will be repeated again and again. You
can use this to create an accompaniment.
6. By pushing the joystick in the +Y direction (forward), you
can also overdub performances over the phrase that is
being held.
e: REC Control Src
g: Manual REC Control
“REC Control Src” selects the modulation source that controls
recording.
If this modulation is on, or if “Manual REC Control” is set to On,
you can record the input signal. If a recording has already been
carried out, additional signals will be overdubbed.
The effect is off when a value for the modulation source specified for
the “REC Control Src” parameter is 63 or smaller, and the effect is on
when the value is 64 or higher.
f: RST Control Src
h: Manual RST Control
The “RST Control Src” parameter specifies the modulation
source that controls the reset operation.
When you set this modulation source to On, or “Manual RST
Control” to RESET, you can erase what you recorded. If the Loop
Time parameter has been set to Auto, the loop time is also reset.
a
Loop Time
[msec]
Auto, 1...10800
Sets Automatic loop time setup
mode or specifies loop time
b
Loop BPM
Sync
Off, On
Specifies whether delay time is set
in milliseconds, or as a note value
relative to tempo
c
BPM
MIDI,
40.00...
300.00 MIDI syncs to the system tempo; 40–
300 sets the tempo manually for this
individual effect
Time Over? ---, OVER!
An error indication that appears if
delay time exceeds the upper limit
when MIDI/Tempo Sync=On
d
Loop Base
Note
r...w
Selects the type of notes to specify
the delay time
Times x1...x32
Sets the number of notes to specify
the delay time
e
REC Control
Src
Off...Tempo Selects control source for recording
f RST Control Src Off...Tempo Selects control source for reset
g
Manual REC
Control REC Off,
REC On Sets the recording switch
h
Manual RST
Control
Off, RESET Sets the reset switch
i
Pan
L100...L1, C,
R1...R100
Sets the stereo image of the effect
Src Off...Tempo
Selects the modulation source of
stereo image of the effect
Amt –100...+100
Sets the modulation amount of
stereo image of the effect
j
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Left
Right
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In - Stereo Out
Pan
Delay
D -mod
D -mod
Loop Time: Auto/ ...5400ms
+
Tempo
BPM
BPM Base Note x Times
REC Control
RST Control