KORG Professional Engineer PA3 - Manual (Page 179)

177 Effects
Double Size
Advanced
a: Sw
This parameter determines how to switch on/off the overdrive
via a modulation source.
When “Sw” = Toggle, overdrive is turned on/off each time the
pedal or joystick is operated.
Overdrive will be switched on/off each time the value of the
modulation source exceeds 64.
When “Sw” = Moment, overdrive is applied only when you press
the pedal or operate the joystick.
Only when the value for the modulation source is 64 or higher, the
overdrive effect is applied.
134: L/C/R Long Delay
This multitap delay outputs three Tap signals to left, right and
center respectively. You can set a maximum of 5,460msec for the
delay time.
135: St/Cross Long Delay
(Stereo/Cross Long Delay)
This is a stereo delay, and can by used as a cross-feedback delay
effect in which the delay sounds cross over between left and
right by changing the feedback routing. You can set a maximum
of 2,730msec for the delay time.
a
L Delay Time
[msec]
0...5460 Sets the delay time of TapL
Level 0...50 Sets the output level of TapL
b
C Delay Time
[msec]
0...5460 Sets the delay time of TapC
Level 0...50 Sets the output level of TapC
c
R Delay Time
[msec]
0...5460 Sets the delay time of TapR
Level 0...50 Sets the output level of TapR
d
Feedback
(C Delay)
–100...+100 Sets the feedback amount of TapC
Src Off...Tempo
Selects the modulation source for
the TapC feedback
Amt –100...+100
Sets the modulation amount of the
TapC feedback
e
High Damp [%] 0...100
Sets the damping amount in the
high range
Low Damp [%] 0...100
Sets the damping amount in the low
range
f
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
g Spread 0...50
Sets the width of the stereo image
of the effect sound
h
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
C Delay
R Delay
Left
Right
Feedback
Spread
FX Amt
FX Amt
FX Amt = 100: Mono In - Stereo Out / FX Amt = 0: Stereo In -Stereo Out
Input Level D-mod
High Damp Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
a Stereo/Cross Stereo, Cross
Switches between stereo delay and
cross-feedback delay
b
L Delay Time
[msec]
0.0...2730.0
Sets the delay time for the left
channel
c
R Delay Time
[msec]
0.0...2730.0
Sets the delay time for the right
channel
d
L Feedback –100...+100
Sets the feedback amount for the
left channel
Src Off...Tempo
Selects the modulation source of
feedback amount
Amt –100...+100
Sets the modulation amount of the
left channel feedback
e
R Feedback –100...+100
Sets the feedback amount for the
right channel
Amt –100...+100
Sets the modulation amount of the
right channel feedback
f High Damp [%] 0...100
Sets the damping amount in the
high range
g Low Damp [%] 0...100
Sets the damping amount in the low
range
h
Input Level
Dmod [%]
–100...+100
Sets the modulation amount of the
input level
Src Off...Tempo
Selects the modulation source for
the input level
i Spread –50...+50
Sets the width of the stereo image of
the effect sound
j
Wet/Dry
Dry, 1:99...99:1,
Wet Balance between the wet and dry
signal
Src Off...Tempo
Table , “Dynamic Modulation
sources,” on page 106
Amt –100...+100 Amount of modulation source
Delay
Delay
Stereo/Cross
Left
Right
Feedback
FX Amt
FX Amt
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp Low Damp
High Damp Low Damp
Spread Stereo/Cross