Panasonic DMR-EH75V - Manual (Page 26)

26
RQT8346
STEP 4 Set up to match your television and the unit’s remote control
This setting allows you to select the type of television connected.
[1]
While stopped
Press [FUNCTIONS].
[2] Press [ 3, 4] to select “Other Functions” and
then press [ENTER].
[3] Press [ 3, 4] to select “Setup” and then press
[ENTER].
[4] Press [ 3, 4] to select “TV Screen” and then
press [ 1].
[5] Press [ 3, 4] to select “TV Type” and then
press [ENTER].
≥Aspect 4:3/Aspect 16:9:
≥480p/480i:
- Select “480p” if the television is compatible with progressive
output.
- Select “480i” if the television is not compatible with
progressive output or you are unsure about television
compatibility.
[6] Press [ 3, 4] to select the item and then press
[ENTER].
You can operate the TV through the unit’s remote control.
Point the remote control at the television
While pressing [ Í, TV POWER] enter the code
with the numbered buttons.
e.g., 0250: [0] > [2] > [5] > [0]
Manufacturer and Code No.
Test by turning on the television and changing channels.
≥Repeat the procedure until you find the code that allows correct
operation.
≥If your television brand is not listed or if the code listed for your
television does not allow control of your television, this remote
control is not compatible with your television.
Change the remote control code on the main unit and the remote
control (the two must match) if you place other Panasonic products
close together.
Use “1”, the factory set code, under normal circumstances.
After performing steps 1 to 3 ( l left)
[4] Press [ 3, 4] to select “Setup” and then press
[ 1].
[5] Press [ 3, 4] to select “Remote Control Code”
and then press [ENTER].
[6] Press [ 3, 4] to select the code (Set Code 1,
Set Code 2, or Set Code 3) and then press
[ENTER].
≥The code on the unit has been set.
[7] While pressing [ENTER], press and hold the
numbered button ([1], [2] or [3]) for more than
2 seconds.
≥The code on the remote control has been set.
[8] Press [ENTER].
∫ When the following indicator appears on the
unit’s display and you are unable to operate the
unit
Press and hold [ENTER] and the indicated number button at the
same time for more than 2 seconds.
To return to the previous screen
Press [RETURN]. To exit the screen
Press [RETURN] several times.
Selecting television type
4:3 standard aspect television 16:9 widescreen television
When connected to a 4:3 standard aspect television
To change how a DVD-Video or DVD-RAM widescreen picture is
shown on a 4:3 standard aspect television
l 77, “4:3 TV Settings for DVD-Video” or “4:3 TV Settings for
DVD-RAM”
DVD/VHS
TV GUIDE
ENTER
FU
NC
TIO
NS
VOLUME CH
CH
TV/VIDEO
POWER
POWER
PAUSE STOP
SLOW/SEARCH
3 2 1
6 4
9 8 7
0 INPUT
SELECT
CM SKIP REC MODE
RETURN SUB MENU
SCHEDULE
DI RE
CT
NA
VIG
AT
OR
DISPLAY AUDIO
REC STATUS
A B
VCR Plus+
DELETE
SKIP/INDEX
TIME SLIP/ JET REW
PLAY
RESET RESET
CANCEL
TRACKING/V-LOCK/PAGE
DRIVE
SELECT
TRACKING/V-LOCK/PAGE
5
Info
CREATE
CHAPTER
ENTER
FU
NC
TIO
NS
VOLUME CH TV/VIDEO
POWER
3 2 1
6 4
9 8 7
0
RETURN
5
3,4,2,1
ENTER
FUNCTIONS
TV operation
buttons
RETURN
REW FF
TV GUIDE
REC
TV GUIDE
¥
Numbered
buttons
Setup
Setup
Disc
Video
Audio
Display
Channel
TV Screen
TV Type
Aspect 4:3 & 480i
Aspect 4:3 & 480p
Aspect 16:9 & 480p
Aspect 16:9 & 480i
ENTER
4:3 TV
16:9 Aspect (Widescreen TV)
VHS
4:3 16:9
Television operation
Panasonic
National
QUASAR 0250/0051 PHILIPS (RC-5) 0054
RCA 0047
SAMSUNG 0060/0587/0702
FISHER 0154 SANYO 0154
GE 0047 SHARP 0165/0093
GOLDSTAR 0178/0457/0317 SONY 0000
HITACHI 0145 SYLVANIA 0054
JVC 0053 THOMSON 0047
LG 0178/0457/0317 TOSHIBA 0156
MAGNAVOX 0054 ZENITH 0017
MITSUBISHI 0150
When other Panasonic products respond
to this remote control
Disc
Setup Remote Control Code
Press “ ±” and “ENTER” together
for more than 2 seconds on the remote.
Channel
Setup
Disc
Video
The unit’s remote control code
M6740P.book 26 ページ ２００６年１月３０日 月曜日 午後３時３０分