Panasonic MC-UG693 - Manual (Page 11)

- 11 -
Handle
Manche
Mango
On /Off Switch
Commutateur marche/arrêt
Interruptor de encendido/apagado
Bag Cover Release
Seguro de la cubierta
de la bolsa
Levier d'ouverture du
couvercle du sac
Height Adjustment Lever
Levier de réglage de hauteur
Palanca para ajustar la altura
Nozzle Cover
Couvercle de la base
Cubierta de boquilla
Headlight
Dispositif
d’éclairage
Luz
Belt
MC-V270B
Courroie
Correa
Nozzle Base
Base de boquilla
Partie inférieure de la base
Bag Cover
Couvercle
du sac
Cubierta
de la bolsa
Latch
S guro
Loquet
e
Furniture Guard
Pare-chocs
Protector de muebles
Loquet
Latch
S guro e
Levier d’ouverture du couvercle
du filtre d’évacuation
Exhaust Filter Cover Release
Liberación de la cubierta
del filtro de escape
Filtre d’évacuation (l’intérieur)
F
Exhaust Filter (Inside)
MC-V191H
iltro de escape (dentro)
Dust Bag
Filtre d’évacuation (l’intérieur)
F
(Inside)
MC-V155M
iltro de escape (dentro)
Carpet/Bare Floor Selector
Sélecteur tapis/plancher
Selector de pisos con
alfombra y sin alfombra
Voltaje Protector termal Extensión de cordón Herramientas
120 V c.a. (60 Hz) Si 10,7 m (35 pi) Si
Alimentation Protecteur thermique Longueur du cordon Accessoires
120 V c.a. (60 Hz) Oui 10,7 m (35 pi) Oui
Diagrama de características
Tableau des caractéristiques
Vacuum Cleaner 1. Unplugged at wall outlet. 1. Plug in firmly, push on/off
won’t run. switch to on.
2. Tripped circuit breaker/blown 2. Reset circuit breaker or
fuse. replace fuse at household
service panel.
3. On /off switch not turned on. 3. Push on/off switch to on.
Poor job of dirt 1. Full or clogged dust bag. 1. Change bag.
pick-up. 2. Wrong pile height setting. 2. Adjust setting.
3. Worn agitator. 3. Replace agitator.
4. Clogged nozzle or bag holder. 4. Check CLOG REMOVAL.
5. Clogged hose. 5. Check for clogs.
6. Hole in hose. 6. Replace hose.
7. Broken/misplaced belt. 7. Replace/fix belt.
8. Hose not inserted fully. 8. Insert hose fully.
9. Motor protection system 9. Check for clogs.
activated.
10. Dirty filters. 10. Change filters.
Vacuum cleaner 1. Wrong pile height setting. 1. Adjust setting.
picks up moveable
rugs or pushes too
hard.
Light won’t work. 1. Burned out light bulb. 1. Change light bulb.
1. Broken belt. 1. Replace belt.
2. Bare floor selector in bare 2. Move selector to the carpet
floor setting. setting.
3. Belt installed incorrectly. 3. Check BELT CHANGING AND
AGITATOR CLEANING.
Air flow restricted 1. Attachment use restricts 1. Check ATTACHMENTS.
with attachment use. air flow.
Sound changes. 2. New carpet fuzz clogged 2. Check CLOG REMOVAL and
air path. clean hose.
Excessive noise as 1. Belt rubbing on carpet/bare 1. Push selector all the way
vacuum cleaner is floor selector shaft. forward.
shut off.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
- 66-
BEFORE REQUESTING SERVICE
Review this chart to find do-it-yourself solutions for minor performance problems.
Any service needed, other than those described in these Operating Instructions,
should be performed by an authorized service representative.
WARNING
Electrical Shock or Personal Injury Hazard
Disconnect the electrical supply before servicing or cleaning the vacuum cleaner.
Failure to do so could result in electrical shock or personal injury from vacuum
cleaner suddenly starting.