Panasonic DMR-E500H - Manual (Page 72)

72
RQT7394
Ref
e
re
nce
Error messages
On the television Page
On the unit’s display
Cannot finish recording
completely. ≥ The program was copy-protected.
≥ The HDD or disc may be full.
—
—
Cannot play. ≥ You inserted an incompatible disc (Discs recorded in PAL video, etc.). —
Cannot record on the disc. ≥ The disc may be dirty or scratched.
≥ You cannot format a Microdrive or mobile hard disk on this unit.
79
— Please check the disc.
Unable to format.
Cannot play back on this DVD-
Recorder.
≥ You tried to play a non-compatible image.
≥ Turn the unit off and re-insert the card.
34
34
Cannot record. Disc is full. ≥ Create space by erasing any unnecessary titles. [HDD] [RAM]
(Even if you erase recorded content from the DVD-R, there is no increase in disc space.)
≥ Use a new disc.
32, 37, 41,
45, 59
—
Cannot record. Maximum
number of titles exceeded.
Error has occurred. Please
press ENTER. ≥ Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering
(“SELF CHECK” appears on the unit’s display).
—
No disc ≥ The disc may be upside down. —
No folders. ≥ There is no compatible folder in this unit. 21
No PC CARD
No SD CARD
No valid PC card.
No valid SD card. ≥ The card is not inserted. If this message is displayed with a compatible card already
inserted, turn off the unit, remove and then re-insert the card.
≥ The card inserted is not compatible or the card format does not match.
34
21
Not enough space on dubbing
destination. ≥ Create space by erasing any unnecessary items.
≥ Erase one or more items registered on the transfer (dubbing) list to ensure that the
“Current capacity” is not exceeded.
32, 35, 37,
41, 44, 45,
59
49, 55
Please change the disc. ≥ There may be a problem with the disc. Press [ < OPEN/CLOSE] on the main unit to remove
it and check it for scratches or dirt. (The unit turns off automatically after you open the tray.)
79
This is a non-recordable disc. ≥ The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.
≥ You inserted an unformatted DVD-RAM. Format the disc with this unit.
—
59 This disc is not formatted
properly.
$ ≥ The operation is prohibited by the unit or disc. —
Cannot connect to the network. ≥ The router etc. is not properly connected. Please check the LAN cable connection and
router’s AC power supply cord and setting (DHCP server setting etc.).
10, 11
No file.
No title. ≥ Make sure the MPEG4 or still pictures have been recorded.
To record MPEG4 titles on the HDD, set “MPEG4 Recording Mode” in the SETUP menu to
“XF”, “SF”, “F”, “N” or “E”.
34, 36
62
CHK REMOTE 
(“ ∑ ” stands for a number.)
≥ The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [ENTER] and the indicated number button at
the same time for more than 2 seconds.
14
HARD ERR ≥ If there is no change after turning the unit on and off, consult the dealer where the unit was
purchased.
—
HDD SLP ≥ In order to extend HDD life, the HDD is in SLEEP mode. Press [HDD] to activate. 79
NO READ ≥ The disc is dirty or badly scratched. The unit cannot record, play, or edit.
≥ You have used a DVD-RAM/PD lens cleaner and it has finished. Press [ < OPEN/CLOSE]
on the main unit to eject the disc.
79
—
PLEASE WAIT ≥ Displayed when the unit is started. This is not a malfunction. —
SELF CHECK ≥ There was a power failure or the AC plug was disconnected while the unit was on. The unit
is carrying out its recovery process. Wait until the message disappears.
—
UNSUPPORT ≥ You have inserted a disc the unit cannot play or record on. 20
U14 ≥ The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling fan
on the rear of the unit.
—
U99 ≥ The unit fails to operate properly. Press [POWER Í /I] on the main unit to switch the unit to
standby. Now press [POWER Í /I] on the main unit again to turn the unit on.
—
7394en.book Page 72 Wednesday, March 30, 2005 9:45 AM