Panasonic DMR-E500H - Manual (Page 8)

8
RQT7394
Ge
tt
in
g s
ta
rte
d
STEP
1
Connection
≥ You need to subscribe to a cable TV service to enjoy viewing their programming.
≥ Consult your service provider regarding appropriate cable TV box.
≥ If you receive your programming solely from a satellite service, the program guide in this unit will not receive program listings or
channel information. Without this information, program-based recordings cannot be made. However, recordings can still be set
manually.
The connection will allow the video cassette recorder to be used for playback when this unit is turned off. For optimum operation, it is
recommended that this unit be connected as shown below.
A to Y are indexes for Spanish Quick Reference.
∫ Should I use the AUDIO/VIDEO OUT terminal or
the RF OUT terminal?
If your cable TV box has both AUDIO/VIDEO OUT terminals and
RF OUT terminals, we recommend connecting the AUDIO/VIDEO
OUT terminal with the unit’s IN3 (L3) terminal. Using this
connection provides better picture quality.
≥ The S-VIDEO terminal achieves a more vivid picture than the
VIDEO terminal.
∫ Why should I connect the IR Blaster?
The IR Blaster is a device that allows this unit to communicate with
the cable TV box. It acts like a remote control for the cable TV box.
If you connect a cable TV box to this unit, you also need to attach
the IR Blaster so this unit can control the channels on the cable TV
box.
Place the IR Blaster in front of the signal sensor of the cable TV box.
Connection with a cable TV box and video cassette recorder
Y P B P R
R - AUDIO - L VIDEO S-VIDEO
OPTICAL G-LINK
COMPONENT VIDEO OUT
(480p/480i) DIGITAL AUDIO OUT
(PCM/BITSTREAM)
IN1 (L1)
IN3 (L3)
R - AUDIO - L VIDEO S-VIDEO OUT1
OUT2
VHF/UHF
RF IN
RF OUT
SUB WOOFER CENTER R L
FRONT
AUDIO OUT
j LAN (10/100) 5.1ch
R - SURROUND - L
VIDEO
RF S-VIDEO
R L
AUDIO
OUT IN
VHF/UHF
RF IN
VHF/UHF
RF OUT
AUDIO
R
AUDIO
L
VIDEO
IN
AUDIO
R
AUDIO
L
VIDEO
OUT
OUT IN
VHF/UHF
RF IN
COMPONENT
VIDEO IN
AUDIO IN
R L S VIDEO IN VIDEO IN
H 75 ≠ coaxial cable
J This unit
U Cable TV box
I Audio/Video cable
Q These connections to IN3 (L3)
are required for the TV Guide
On Screen
TM system to work.
B Television
I Audio/Video cable
S Instead of using the Audio/
video cable, you can also
connect the RF IN terminal
on this unit to the cable TV
box RF OUT terminal using
the 75
≠ coaxial cable.
T Setting the IR Blaster
➡ below
P IR Blaster
Insert the IR Blaster jack into the G-
LINK terminal.
≥ Only use the included IR Blaster.
C Red White Yellow
F Video cassette recorder
C Red White Yellow
C Red White Yellow
G Yellow
White
Red
E Splitter
H 75 ≠ coaxial cable
I Audio/Video cable
N AC power supply cord
Connect only after all other
connections are complete.
O To household AC outlet
(AC 120 V, 60 Hz)
L To IN1 (L1) K To OUT1 or OUT2
R To IN3 (L3)
C Red White Yellow
M Cooling fan
indicates included accessories.
indicates accessories not included. A
D Cable from wall or antenna signal
Setting the IR Blaster
V Read the cable TV box operating
instructions regarding positioning of the
signal sensor.
W If necessary, use the double sided adhesive tape (included) to
secure the IR Blaster to a flat surface.
Y If you peel off the adhesive tape, the surface may become
damaged.
Once you have confirmed the cable TV box is operating
correctly, secure it by attaching the adhesive tape.
X e.g. Television stand surface
U Cable TV box
新セットアップ .fm Page 8 Monday, March 28, 2005 3:47 PM