Nilfisk-Advance America Terra 5200B - Manual (Page 17)

INSTRUCTIONS FOR USE
146 1996 000(2)2004-08 – Terra™ 5200B 15
6. Disconnect the battery connector (4, Fig. V) and
connect it to the external battery charger.
7. Connect the battery charger to the electrical mains
and charge the batteries.
8. When the recharging is complete, disconnect the
battery charger from the electrical mains and from the
battery connector (4, Fig. V).
9. Check the correct level of electrolyte inside the
batteries and close the caps (3, Fig. V).
10. Reconnect the battery connector (4, Fig. V) to the
machine.
11. Disengage the lock rod (16, Fig. V) and close the
hood (13, Fig. C); the machine is ready to be used.
SAFETY FUNCTIONS
The machine is equipped with the following safety
functions.
RUNNING CONSENT SWITCH
It allows the machine to run only if the operator is on the
driver's seat (27, Fig. B).
EMERGENCY PUSH-BUTTON
It is in the position 12, Fig. B, easily accessible for the
operator; it must be pressed when it necessary to stop the
machine operation immediately.
HOPPER LIFTING/LOWERING CONSENT
PUSH-BUTTON
It is in the position 1, Fig. B and must be pressed and held
to activate the hopper lifting/lowering and overturning
push-buttons.
HOPPER LIFTING CYLINDER SAFETY
DEVICE VALVE
It is located on the hopper lifting cylinder.
It stops the hopper in the position it has reached (without
possibility for it to lower accidentally) if the hydraulic
system piping, feeding the lifting cylinder, should break.
TROUBLESHOOTING
For further information consult the Service Manual at any
Nilfisk Service Center.
TROUBLE REMEDY
After having turned the ignition
switch (18, Fig. B) to “I”
position, the display does not
illuminate and the machine
does not work
Check that the battery connector
(4, Fig. V) is correctly connected to
the machine
Check the integrity of the following
fuses: F1 (1, Fig. Z) and F0 (2, Fig.
Z)
The machine does not move
when pressing the accelerator
pedal
Turn the ignition switch to “0”
position, then to “I” position, being
careful not to press the accelerator
pedal during this operation
The main broom does not work
Check that the related thermal
circuit breaker (5, Fig. V) is not
deactivated; otherwise reactivate it
by pressing the related key
The side brooms do not work
Check that the related thermal
circuit breaker (6 or 7, Fig. V) is not
deactivated; otherwise reactivate it
by pressing the related key
The machine operates only
when stationary, otherwise it
switches off and the red
warning light turns on
Re-charge the battery.
If the problem persists, replace the
batteries
The machine collects few
debris/dust
Check that the dust filter (4, Fig. N)
is not obstructed
Check that the hopper (4, Fig. C) is
not full
Check that the skirts (16, 17, 18,
19, Fig. C) are not broken or
incorrectly adjusted
Check the correct height of the
brooms (10, 11, 12, Fig. C)
The battery autonomy is low
Install a battery with greater
capacity: (240 Ah)
The hopper does not lift
Check the fuse (F2, Fig. Z)
integrity
The hopper does not overturn
Check the fuse (F3, Fig. Z)
integrity
Check that the hopper is lifted from
the ground at an height greater
than 10.6 in (270 mm)
The hopper does not lower
Before lowering the hopper by
pressing the push-button (15, Fig.
B), check that the hopper is in its
horizontal position by pressing the
push-button (16, Fig. B)
The filter shaker does not work
Operate the lever (24, Fig. B) to
check that the main broom is lifted
Check the fuse (F4, Fig. Z)
integrity