NordicTrack ELITE NTL19007.1 - Manual (Page 23)

23
THE INFORMATION MODE
The console features an information mode that allows
you to view treadmill usage information, select a sys-
tem of measurement for the console, and turn on and
turn off the demo mode. The information mode also al-
lows you to adjust the settings of the television and to
save channels into the television’s memory.
Follow the steps below to use the information mode.
1. Press the Stop button while inserting the key
into the console.
When the information mode is selected, the lower
part of the screen will show the total number of
miles or kilometers that the walking belt has moved
(Distance) and the total number of hours that the
treadmill has been used (Time).
In addition, the center of the display will show the
word “English” for English miles or the word “Metric”
for metric kilometers. Press the Speed increase
button to change the unit of measurement if de-
sired.
Note: The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. While the demo mode is turned on, the
console will function normally when you plug in the
power cord, switch the reset/off circuit breaker to
the reset position, and insert the key into the con-
sole. However, when you remove the key, the dis-
plays will remain lit, although the buttons will not
function. If the demo mode is turned on, the words
“DEMO ON” will appear on the screen while the in-
formation mode is selected. To turn on or turn off
the demo mode, press the Speed decrease button
until the words “DEMO OFF” appear on the screen.
While the information mode is selected, you can
select an audio setting for the iFIT personal trainer,
if desired. If you select the All setting, the personal
trainer will give you detailed instructions to help
you through your workout. If you select the On set-
ting, the personal trainer will simply guide you
through the workout. If you select the Off setting,
the personal trainer will be silent. To select a per-
sonal trainer audio setting, press the incline in-
crease or decrease button.
2. Press the TV Power button and adjust the
brightness, contrast, color, sharpness, and/or
hue of the television.
When you press the TV Power button, the brightness
level indicator will appear on the television screen.
Press the Volume (VOL.) buttons to adjust the
brightness setting if desired.
Next, press the Channel (CHAN.) buttons until the
contrast, color, sharpness, or hue level indicator ap-
pears. Adjust the settings, if desired, by pressing the
Volume buttons.
3. Press the TV button again and add or delete
channels.
Note: Complete this step only if you are using ana-
log cable.
After all valid cable channels available in your area
have been saved into the television’s memory (see
step 5 on this page), you can manually add chan-
nels or delete unwanted channels.
To add or delete a cable channel, first press the
Channel buttons until the desired channel number
appears on the screen. Then, press the Volume in-
crease button to add the channel, or the Volume
decrease button to delete the channel. Continue
this process until you have added all desired chan-
nels and deleted all unwanted channels.
4. Press the TV Power button again and select a
cable connection if necessary.
If you have connected a CATV cable, one of the
three Cable settings should be selected; try all
three Cable settings, if necessary, to find the opti-
mal setting. Press the Volume increase button to
select the Standard Cable setting, the Channel de-
crease button to select the Cable IRC setting, or
the Channel increase button to select the Cable
HRC setting.
5. Press the TV button again and save cable chan-
nels into the television’s memory.
When you press the TV button, the television will
begin scanning all of the cable channels available
in your area. When no cable signal is detected on
a channel, the channel will be skipped. When a
cable signal is detected, the channel will be saved
into memory and the next channel will be selected.
This process will continue until the highest channel
is reached.
Do not remove the key while the
television is scanning channels. Note: If you are
viewing channels through an external source such
as a cable box or a VCR, the television will save
only the channel used by the external source.
6. When you are finished using the information
mode, remove the key from the console.
To exit the information mode at any time (except
while saving channels), remove the key from the
console.