Napco Security Technologies GEM-P1664 - Manual (Page 36)

X
GEM-P1664 Installation Instructions
L
NAPCO Security Systems
WI1424A 1/06

Page 36
Inhibit System Trouble Audible at Keypad (Do not program in UL installations)
For installations where an audible during a system trouble is not desired, an option, Inhibit System Trouble Audible can be enabled.
Regardless of the system status (Armed or Disarmed) there is no keypad sounder in the event of a system trouble. However, the
trouble will still scroll in the keypad display until [RESET] is pressed and the SYS TBL icon will display until the trouble is restored.
• To disable System Trouble Audible, enable the option Disable System Trouble Audible in the QL-Windows Keypad Features
screen.
Interior Stay Zones; Interior Normally Bypassed (Stay Mode); Auto Interior Bypass (Stay)/Easy Exit
Removal of a programmed group of interior (Stay) zones from the system will permit freedom of movement throughout the premises
but still allow protection from intrusion through armed perimeter zones. Pressing
E prior to arming will select the Interior Zones,
then arm to bypass. The next time the control panel is disarmed, all bypassed zones will automatically revert to non-bypassed
(disarmed) zones. When
E is pressed, the "BYPASS" reminder will come on.
The bypassed zones may be displayed on the keypad (see GEM-RP1CAe2 FUNCTION MODE).
If Interior Normally Bypassed is selected, all Interior (Stay) zones will always be inactive. The "BYPASS" reminder will always display,
indicating that only partial protection will be provided upon arming. To temporarily restore interior protection, press
E ; the
"BYPASS" reminder will go out upon arming, denoting full protection, however Interior (Stay) Zones will once again be bypassed the
next time the panel is disarmed.
If "Auto Interior Bypass/Easy Exit" is programmed, all Interior Zones will automatically be bypassed if the Exit/Entry doors are not
opened during exit delay. If
D
is pressed while armed with Interior Bypassed (Stay), exit delay will restart and Exit/Entry doors may
be opened to permit someone to exit (while others remain on premises) without causing an alarm.
Interior (STAY) Bypass
Interior Zones, when bypassed, allow free movement within the home while the protection of armed perimeter zones is maintained.
To bypass Interior Zones, enter your User Code and press
P. All zones (including Interior Bypass Zones) are all protected with
full protection, in ARMED AWAY mode.
Jumpers (Refer to Wiring Diagram for UL configuration)
JP1: Keypad Configuration Jumper (top center) is installed across top and center pins for normal operation. When configuring GEM-
RP1CAe2 and GEM-K1CA keypads, move jumper across center and lower pins.
JP3: 2-Wire Fire jumpers. Select Zones 7 and/or 8 for use as either 2-Wire Fire Zones or Burglary Zones.
KeyFob Control of Relay Groups 1 and 2
The GEM-P1664 supports KeyFob Control of Relay groups 1 and 2. The KeyFob Aux 1 and Aux 2 buttons can be programmed to
toggle on and off external Relay Groups 1 and 2.
KeyFob Arm/Disarm chirp of Alarm Output.
The Key Fob Arm/Disarm chirp can be directed to the Alarm Output, which can free up the PGM2 Output for other uses such as
garage door opener control. To enable the Key Fob Arm/Disarm chirp option on Alarm Output, enable 'Chirp' Output on KeyFob Arm/
Disarm and Select Alarm Output for KeyFob 'Chirp' in the PCD-Windows Options screen.
Keyfob Transmitters; Chirp Output on Keyfob; Select Alarm for Keyfob Chirp
Keyfob transmitters can (1) operate up to four zones, or (2) can Arm/Disarm an area and provide two Auxiliary control buttons, but
cannot be operated in these two modes simultaneously. A Keyfob Transmitter set up to Arm/Disarm an area with "PGM2 Chirp on
Keyfob Arm/Disarm" will cause a 1chirp sound on arming and a 2 chirp sound on disarming, by using an steady state Alarm Output
(not a Pulse Alarm, Cadence Pulse Alarm or Voice Siren Driver). Programming the Auxiliary Keyfob Buttons to "C: PGM2 Output
Toggle" on Auxiliary 1 or 2 buttons will cause PGM2 to toggle the current condition of the PGM2 output. Keyfob 1-8 can have their
opening / closings reported as users 57 through 64, respectively.
Keypad Area Assignments
In multiple-area systems, each keypad must be individually configured to the correct keypad number. No two keypads can possess
the same keypad number. No keypad numbers can be skipped (they must be contiguous). Note that each address comprises 2
nibbles; enter the Area Number in the right nibble.
Keypad Digital Dialer Test
A Digital Dialer Test (Central Station Comm. Test) can be initiated from the function menu. Press
R until "DIGITAL DIALER
TEST Y/N" is displayed and then press [NEXT/YES] to initiate the transmission of a Test Timer signal. Note: Test Timer reporting
codes and Report Test Timer on Telco1 or Telco 3 must be programmed.
Keypad Jumpers (GEM-RP1CAe2 / GEM-K1CA)
Refer to label LA1374 on the circuit board fishpaper for jumper locations and a summary of settings.
Glossar
y