Onkyo DR-S2.2 - Manual (Page 26)

26 26
Before connecting
• Make sure that all the connections from pages 15 to 25 are
complete (the connection to the TV is required).
• Turning on the DVD Receiver may cause a momentary power
surge, which might interfere with other electrical equipment such
as computers. If this happens, use a wall outlet on a different
circuit.
(European and some Asian models)
• The DVD Receiver is shipped with the main power (POWER)
switch in the on position ( _ ON). When the power cord is
plugged in for the first time, the DVD Receiver will automatically
enter the standby state (same condition after step 2 below).
Connecting the Power/
Turning on the DVD Receiver
1
2
3
Connect the power cord to a wall
outlet.
(Other than European and some Asian
models)
The DVD Receiver enters the standby
mode and the STANDBY indicator lights
up.
(European and some Asian models
only)
Press POWER to switch on the
main power to put the DVD
Receiver in the standby mode.
The STANDBY indicator lights up.
• The buttons on the remote controller do
not operate if the POWER switch is set
to OFF.
• To switch off the main power, press
POWER again.
Press STANDBY/ON on the DVD
Receiver or ON on the remote
controller to turn on the DVD
Receiver.
The light and display on the DVD
Receiver’s front panel light. At the same
time, the STANDBY indicator goes off.
• To put the DVD Receiver in the standby
mode, press STANDBY/ON on the DVD
Receiver, or STANDBY on the remote
controller. Be sure to set the volume to
minimum before putting the DVD
Receiver in the standby mode for the
next use to avoid sudden loud sound
reproduction.
• While in the STANDBY mode, the DVD
Receiver can receive signals from the
remote controller. However, if you press
POWER on the DVD Receiver to switch
off the main power, the remote
controller cannot be used to turn on the
DVD Receiver.
• Setting the STANDBY button to standby
does not shut off the power completely.
■ Setting the TV System (Other than North
American model)
The default setting of the DVD Receiver is AUTO, and unless you
notice that the picture is distorted when playing some discs, you
should leave it set to AUTO.
If you experience picture distortion with some discs, set the TV
system to match your country or region’s system. Doing this,
however, may restrict the kinds of disc you can watch. The table
below shows what kinds of disc are compatible with each setting
(AUTO, PAL and NTSC).
1 Switch the DVD Receiver into standby.
2 Hold down
¢ then press STANDBY/ON until the display
indicates the new setting to switch the TV system.
The TV system changes as follows:
AUTO
= NTSC
NTSC = PAL
PAL = AUTO
Note that you have to switch the player into standby before each
change.
About MOD. (Modulation) PAL
• SHRINK
Most models of the newly developed countdown PAL TV system
detect 50 Hz (PAL)/60 Hz (NTSC) and automatically switch
vertical amplitude, resulting in a display without vertical
shrinkage.
• If your PAL TV does not have a V-Hold control, you may not be
able to view NTSC disc because the picture may roll. If the TV
has a V-Hold control, adjust it until the picture stops rolling. On
some TVs, the picture may shrink vertically, leaving black bands
at the top and bottom of the screen. This is not a malfunction; it is
caused by the NTSC
= PAL conversion.
Type
DVD
Video CD
CD, No disc
Format
NTSC
PAL
NTSC
PAL
Disc Output format
Position of TV SYSTEM mode
NTSC PAL AUTO
NTSC MOD. PAL NTSC
PAL PAL
NTSC MOD. PAL NTSC
NTSC PAL PAL
NTSC PAL NTSC or PAL
STANDBY indicator
STANDBY/ON
POWER (European and some Asian models only)
Display Front panel
illumination