Omron CQM1H-CLK21 User Manual
Operation manual, Controller link units
Advertising
This manual is related to the following products:
Table of contents
Document Outline
- CS1W-CLK21-V1 CJ1W-CLK21-V1 C200HW-CLK21 CVM1-CLK21 CQM1H-CLK21 (CS1W-RPT01/02/03 Repeater Units)
- Notice:
- Unit Versions of CS/CJ-series Controller Link Units
- About this Manual:
- Warranty
- PRECAUTIONS
- SECTION 1 Features and System Configuration
- SECTION 2 Basic Procedures
- SECTION 3 Installation and Wiring
- 3-1 Component Names and Functions
- 3-1-1 CS-series Controller Link Units
- 3-1-2 CJ-series Controller Link Units
- 3-1-3 C200HX/HG/HE Controller Link Unit
- 3-1-4 CVM1 and CV-series Controller Link Unit
- 3-1-5 CQM1H-series Controller Link Unit
- 3-1-6 Wire-to-Wire Repeater Unit
- 3-1-7 Wire-to-Optical (H-PCF) Repeater Unit
- 3-1-8 Wire-to-Optical (GI) Repeater Unit
- 3-2 Unit Installation
- 3-3 Wiring
- 3-4 Constructing Networks with Repeater Units
- 3-1 Component Names and Functions
- SECTION 4 Preparations for Communications
- SECTION 5 Data Links
- SECTION 6 Message Service
- 6-1 Introduction
- 6-2 Selecting Communications Instructions
- 6-3 Using the Message Service
- 6-4 FINS Commands and Responses
- 6-5 Commands and Responses for Controller Link Units
- 6-5-1 Command Codes
- 6-5-2 DATA LINK START
- 6-5-3 DATA LINK STOP
- 6-5-4 CONTROLLER DATA READ
- 6-5-5 CONTROLLER STATUS READ
- 6-5-6 NETWORK STATUS READ
- 6-5-7 DATA LINK STATUS READ
- 6-5-8 ECHOBACK TEST
- 6-5-9 BROADCAST TEST RESULTS READ
- 6-5-10 BROADCAST TEST DATA SEND
- 6-5-11 ERROR LOG READ
- 6-5-12 ERROR LOG CLEAR
- 6-6 Commands and Responses for C200HX/HG/HE and CQM1H-series PLCs
- 6-6-1 Command Codes
- 6-6-2 Memory Area Designations
- 6-6-3 MEMORY AREA READ
- 6-6-4 MEMORY AREA WRITE
- 6-6-5 MULTIPLE MEMORY AREA READ
- 6-6-6 PROGRAM AREA READ
- 6-6-7 PROGRAM AREA WRITE
- 6-6-8 RUN
- 6-6-9 STOP
- 6-6-10 CONTROLLER DATA READ
- 6-6-11 CONTROLLER STATUS READ
- 6-6-12 CLOCK READ
- 6-6-13 CLOCK WRITE
- 6-6-14 ERROR CLEAR
- 6-6-15 FORCED SET/RESET
- 6-6-16 FORCED SET/RESET CANCEL
- 6-6-17 MULTIPLE FORCED STATUS READ
- 6-7 Response Codes
- SECTION 7 Network Interconnections
- 7-1 What is Network Interconnection?
- 7-2 Remote Programming and Monitoring
- 7-3 Routing Tables
- 7-4 Setting Routing Tables
- 7-4-1 Routing Table Setting Procedure
- 7-4-2 Editing Local Network Tables
- 7-4-3 Editing Relay Network Tables
- 7-4-4 Saving Routing Tables
- 7-4-5 Connecting to the PLC
- 7-4-6 Routing Table Enable Bit (C200HX/HG/HE and CQM1H-series Only)
- 7-4-7 Transferring Routing Tables
- 7-4-8 Example Routing Table Settings
- SECTION 8 Communications Timing
- SECTION 9 Troubleshooting and Maintenance
- SECTION 10 Adding Nodes and Editing Active Data Link Tables
- Appendix A Standard Models
- Appendix B Memory Areas
- Appendix C Using the Relay Terminal Block
- Index
- Revision History