Weider 16.8ST - Manual (Page 16)

16
34. Route the Low Cable (72) through the indicated slot
in the Main Upright (3) and the Base (8).
Wrap the Low Cable (72) around a 4Ó Pulley (35) in
the direction shown. Attach the Pulley inside the weld-
ed bracket on the Main Upright (3) with a 3/8Ó x 2Ó
Bolt (62) and a 3/8Ó Nylon Locknut (50) as shown.
50
3
72
8
35
62
Slot
32. Locate the Low Cable (72), which is the only remain-
ing Cable. Note that it has a large ball on one end
and a small ball on the other.
Route the small ball on the Low Cable (72) through
the indicated slots in the Leg Lever (29) and the front
leg on the Base (8).
Attach a 4Ó Pulley (35) inside the slot in the front leg
of the Base (8) with a 3/8Ó x 2 1/2Ó Bolt (54), two 3/8Ó
Flat Washers (55), two 5/8Ó x 1/2Ó Pulley Bushings
(42), and a 3/8Ó Nylon Jam Nut (63).
33. Attach a 4Ó Pulley (35) inside the slot in the Leg Lever
(29) with a 3/8Ó x 2 1/2Ó Bolt (54), two 3/8Ó Flat
Washers (55), two 5/8Ó x 1/2Ó Pulley Bushings (42),
and a 3/8Ó Nylon Jam Nut (63).
Attach the 1/2Ó x 1 3/4Ó Bushing (94) inside the bot-
tom of the Leg Lever (29) with a 5/16Ó x 2 1/2Ó Bolt
(96), two 5/16Ó Flat Washers (80), and a 5/16Ó Nylon
Jam Nut (79).
Refer to the inset drawing. Press the Tab (93) onto
the cage as shown. Secure the Tab with a 1/4Ó x 1Ó
Bolt (95), a Large Washer (104), and a 1/4Ó Nylon
Locknut (25). Make sure that the Low Cable (72) is
on top of the Tab and the 1/2Ó x 1 3/4Ó Bushing (94).
Press a 2Ó Square Inner Cap (33) into the bottom of
the Leg Lever (29). Note: It may be easier to attach
the 2Ó Square Inner Cap and the 1/2Ó x 1 3/4Ó
Bushing (94) if you pivot the Leg Lever upward.
32
55
42
72
29
8
63
Slots
Large Ball
42
55
54
35
34
33
63
79
54
96
29
33
42
94
Slot
42
55
55 72
35
95
104
25
72
80
Cage
Bracket
31
35
72
35
Adjustment
Holes
44
35. Wrap the Low Cable (72) over a 4Ó Pulley (35). Slide
the Pulley and a Cable Trap (44) between the two
Pulley Plates (31). Make sure the Cable is in the
groove of the Pulley and that the Cable Trap is
oriented so it will hold the Cable in place.
Attach the 4Ó Pulley (35) and the Cable Trap (44) to
the lowest holes in the Pulley Plates (31) with a 3/8Ó x
1 3/4Ó Bolt (60) and a 3/8Ó Nylon Jam Nut (63).
60
63
93