Grain Systems Unload Augers PNEG-1057 - Manual (Page 25)

Operation & Maintenance
17
PNEG 1057 - 8" & 10" Commercial Vertical Bin Unloading Auger
Product No. Bin Dia. H.P.
GFC10240 24' 5 14' -6" x 7" O.D. Flight
GFC10270 27' 5 16' -0" x 7" O.D. Flight
GFC10300 30' 5 17' -6" x 7" O.D. Flight
GFC10330 33'-34' 5 19' -6" x 7" O.D. Flight
GFC10360 36' 7 1/2 20' -6" x 7" O.D. Flight
GFC10380 37'-39' 7 1/2 22' -6" x 7" O.D. Flight
GFC10400 40' 7 1/2 23' -0" x 7" O.D. Flight
GFC10420 42' 7 1/2 24' -0" x 7" O.D. Flight
GFC10480 48'-49' 7 1/2 27' -0" x 7" O.D. Flight
GFC10540 54'-55' 7 1/2 30' -0" x 7" O.D. Flight
GFC10600 60' 10 33' -0" x 7" O.D. Flight
GFC10630 63' 10 34' -6" x 7" O.D. Flight
GFC10680 68'-69' 10 37' -6" x 7" O.D. Flight
GFC10720 72' 10 39' -0" x 7" O.D. Flight
GFC10750 75' 10 40' -6" x 7" O.D. Flight
GFC10780 78' 10 42' -6" x 7" O.D. Flight
GFC10800 80' 15 44' -6" x 7" O.D. Flight
GFC10820 82' 15 45' -6" x 7" O.D. Flight
GFC10900 90' 15 49' -6" x 7" O.D. Flight
GFC10920 92' 15 50' -6" x 7" O.D. Flight
Flight Length
10" Horizontal Flights for Vertical Height Unloaders
2. 10" Vertical Commercial Bin Unloading Auger Operating Instructions
A.
Parts Included: 16’-6" vertical auger, horizontal tube 30" long with flange, horizontal drive with 2 or 3 belt drive,
2 belt vertical drive with pulleys, “B” section belts, motor mount, mounting brackets, belt guard and 3' discharge
spout. Your horizontal unloading flight should be ordered separately.
B.
Capacity: For cases with high moisture or high capacity requirements, use the next size larger motor.
( See Capacity Chart Below.)
C.
Vertical Drive: Use a 4.6" motor pulley for recommended auger speed of 408 RPM.
D.
Horizontal Drive: Use a 3.4" motor pulley for recommended auger speed of 323 RPM.
MATERIAL CAPACITY - 10"
Dry Grain 1600-2000
High Moisture 1300-1600
Motor pulleys are NOT furnished with the auger.
E.
Vertical Horsepower:
Use a 7-1/2 H.P. Motor
F.
Horizontal Horsepower:
Use the horsepower chart below to find the flight length to fit your needs.
G. The horsepower recommendations are for augering reasonably dry grain. High moisture grain (above 15%) will
require greater power if maximum capacity is to be maintained. The maximum possible capacity will be less
with high moisture grain than with dry grain. Use an electric motor of the correct size that operates at
1750 R. P. M.
Electrical controls and wiring should be installed by a qualified electrician. The motor
disconnect switches and conductor cables should comply with the National Electrical
Code and any local codes which apply. Motor starting control stations should be so
located that the operator can see that all personnel are clear of the equipment.