Flight & shield assembly, Assembly – Grain Systems Unload Augers PNEG-1050 User Manual
Page 19
19
12" & 14" Commercial Bin Sweep Augers PNEG-1050
Assembly
3. FLIGHT & SHIELD ASSEMBLY
1st Section
12"
w/ cutback 2nd Section 3rd Section
4th Section
5th Section
6th Section
Catalog
Bin
attached
to
from from from from from
Number
Diameter
Drive unit
Drive unit
Drive unit
Drive unit
Drive unit
Drive unit
GCS14360
24'
9'- 9 3/4"
6' - 7 1/2"
GCS14370
37'
9'- 9 3/4"
7' - 1 1/2"
GCS14400
40'
9'- 9 3/4"
8' - 7 1/2"
GCS14420
42'
9'- 9 3/4"
9' - 3 1/2"
GCS14430
43'
9'- 9 3/4"
9' - 9 3/4"
GCS14480
48'
9'- 9 3/4"
7' - 1 1/2"
5'- 3 1/2"
GCS14490
49'
9'- 9 3/4"
8'- 10"
3' - 9 1/2"
GCS14540
54'
9'- 9 3/4"
8'- 10"
6' - 7 1/2"
GCS14550
55'
9'- 9 3/4"
8'- 10"
7' - 1 1/2"
GCS14590
59'
9'- 9 3/4"
9'- 3 1/2"
8' - 7 1/2"
GCS14600
60'
9'- 9 3/4"
9' - 9 3/4"
8' - 7 1/2"
GCS14620
62'
9'- 9 3/4"
9' - 3 1/2"
9'- 3 1/2"
GCS14680
68'
9'- 9 3/4"
6' - 7 1/2"
8'- 10"
6'- 7 1/2"
GCS14720
72'
9'- 9 3/4"
7' - 1 1/2"
9'- 9 3/4"
7'- 1 1/2"
GCS14750
75'
9'- 9 3/4"
7' - 1 1/2"
9'- 3 1/2"
9'- 3 1/2"
GCS14780
78'
9'- 9 3/4"
9' - 3 1/2"
9'- 3 1/2"
8' - 7 1/2"
GCS14800
80'
9'- 9 3/4"
9' - 9 3/4"
9'- 9 3/4"
8' - 7 1/2"
GCS14880
88'
9'- 9 3/4"
6' - 7 1/2"
8' - 10"
6' - 7 1/2"
9' - 9 3/4"
GCS14900
90'
9'- 9 3/4"
3' - 9 1/2"
9'- 9 3/4"
9' - 3 1/2"
9' - 9 3/4"
GCS14920
92'
9'- 9 3/4"
7' - 1 1/2"
8' - 10"
8' - 10"
8' - 10"
GCS14105
105'
9'- 9 3/4"
5' - 3 1/2"
9'- 9 3/4"
9' - 9 3/4"
9' - 9 3/4"
5' - 3 1/2"
GCS14113
113'
9'- 9 3/4"
8'- 10"
9'- 9 3/4"
8' - 10"
9' - 9 3/4"
6' - 7 1/2"
GCS14120
120'
9'- 9 3/4"
9' - 3 1/2"
9'- 9 3/4"
9' - 9 3/4"
9' - 9 3/4"
8' - 7 1/2"
Sweep Flight and Back Shield Sections
A Commercial Bin Sweep can be made up of several
sections of flighting and back shields. The quantity and
lengths of the sweep flight and back shield sections will
vary depending on the bin size. Use the chart below for the
number and length of sections for your size of bin.
The sweep flight with a cut back must connect to the drive
assembly. The remaining sections should be assembled in
the order shown in the chart below. The section furthest
from the drive has mounting holes for the sweep tractor.
The assembly instructions in this section cover assem-
bling the complete Commercial Sweep. Refer to pages 30-
33 and read where use of only a part of the sweep auger
may be recommended when starting to sweep unload a
bin, particularly a large bin. You may choose to only
assemble one or two sections of sweep flight, back
shields, and bearing stands for initial sweep unloading.
Remember, any number of sweep sections can be used
together up to a maximum of six. If a sweep auger with
four or more sections was selected, a truss assembly is
included. The truss should be used when four or more
sections are assembled together. Refer to page 24 for
truss assembly instructions. If the truss assembly you
have is for a greater number of sweep auger sections
than you are assembling, be sure to tie off the extra
cable length so it does not become entangled in the
sweep auger.