Net Optics iLink Agg Link Aggregator Tap User Manual

Quick install guide ilink agg link aggregator tap, Ilink agg, Mounting ilink agg

Advertising
background image

2.  Launch  terminal  emulation  software  such  as  

HyperTerminal  or  minicom  with  the  following  settings:
115200  baud,  8  data  bits,  no  parity,  1  stop  bit,  no  
ÀRZFRQWURO

3.  Connect  power  to  iLink  Agg.  

Make  sure  that  you  connect  the  power  supplies  to  
two  separate,  independent  power  sources.

4.  At  the  login  prompt,  type  admin;;  at  the  password  

prompt,  type  QHWRSWLFV.

5.   Change  the  password  for  the  admin  account.  Type:  
  XVHUPRGQDPH DGPLQSULY SZ <new-­pw>  

where  <new-­pw>  is  the  new  password

6.  Set  the  iLink  Agg  IP  address.  Type:

sysip  set  ipaddr=<ipaddress>  mask=<netmask>
  gw=<gateway>
V\VLSFRPPLW
where  <ip  address>  is  the  IP  address  for  iLink  Agg,  
<netmask>  is  the  netmask,  and  <gateway>  is  the  IP  
address  of  the  gateway

7.  For  more  information  on  the  CLI,  type  +HOSto  display  

command  information,  or  see  the  User  Guide.  The  
tab  key  or  space  bar  can  be  used  to  autocomplete  
partially  typed  commands.  Entering  ?  following  a  
command  (and  a  space)  displays  the  arguments  for  
that  command.  The  up-­  and  down-­arrow  keys  access  
the  CLI  command  history  buffer.  

The  CLI  can  now  be  accessed  remotely  by  SSH  over  the  
iLink  Agg  Management  port.  Connect  the  Management  
port  (the  top  RJ45  on  the  rear  panel)  with  a  CAT5  cable  
to  a  switch  or  hub  to  access  the  CLI  over  the  network.  
The  default  SSH  username  is  OLQNDJJ,  the  password  
is  QHWRSWLFVand  the  port  is  22.  Use  the  SDVVZG  
command  to  change  the  SSH  password.

Mounting iLink Agg

iLink  Agg  is  designed  to  mount  in  a  19-­inch  rack,  
occupying  1U  of  height.  

Slide  the  chassis  into  the  rack  

and  fasten  it  in  place  at  the  front  panel  ears  using  
the  supplied  screws  and  washers.  

Make  sure  that  the  

rack  is  properly  grounded.

Quick Install Guide

iLink Agg Link Aggregator Tap

Unpacking and Inspection

Carefully  unpack  iLink  Agg

TM

 and  retain  materials  for  

later  use.  

iLink  Agg  ships  with  the  following:

‡ (1)  the  iLink  Agg  device
‡ (2)  Power  cords  (AC  model  only)
‡ (1)  Cisco  DB9  to  RJ45  console  cable,  6  ft.,  for  use  

with  the  CLI

‡ Screws  and  washers  for  rack  mounting
‡ (1)  iLink  Agg  Quick  Install  Guide  (this  sheet)
‡ (1)  CD  containing  the  iLink  Agg  User  Guide  and  the  

iLink  Agg  CLI  Command  Reference

‡ Service  Plan  Reference  Guide
‡ Registration  instruction  card

‡ Extended  Warranty  if  purchased  

Carefully  check  the  packing  slip  against  parts  received.  
If  any  part  is  missing  or  damaged,  contact  Net  Optics  
Customer  Service.  (Note:  SFP  modules  are  ordered  
and  shipped  separately.)

&RQÀJXULQJL/LQN$JJ

$OOFRQ¿JXUDWLRQRSWLRQVVWDWXVDQGVWDWLVWLFVDUH  
accessible  from  the  Command  Line  Interface  (CLI).  To  
XVHWKH&/,RYHUDUHPRWH66+FRQQHFWLRQ¿UVWVHWWKH
system’s  IP  address  using  the  local  RS232  interface.  

7RDFFHVVWKH&RPPDQG/LQH,QWHUIDFH
1.  Connect  a  PC  with  terminal  emulation  software  to  

iLink  Agg  using  the  supplied  DB9  to  RJ45  cable.  

Management  Port

Console  Port

For  use  with  -­48V  Only

-

+

For  use  with  -­48V  Only

-

+

Management  Port

Console  Port

Earth

Ground

-48VDC

Return

-48VDC

Return

Power Source 1

Power Source 2

AC Models

DC Models

Independent Power Sources

 PESV1HWZRUN3RUWV 5-

 *LJ0RQLWRU3RUWV 6)3

 *LJ0RQLWRU3RUWV 6)3

 *LJ6;RU/;)LEHU1HWZRUN3RUWV /&W\SH

 *LJ0RQLWRU3RUWV 6)3

 *LJ1HWZRUN3RUWV 6)3

&RSSHU,QOLQH0RGHOV

)LEHU,QOLQH0RGHOV

6SDQ0RGHOV

©  2012  by  Net  Optics,  Inc.  Net  Optics®  is  a  registered  trademark  of  Net  Optics,  Inc.  iLink  Agg

TM

 is  a  trademark  of  Net  Optics,  Inc.    

800-­0128-­001  rev  B  PUBDIRPQ  3/10

iLink Agg

TM

Advertising