Xylem C3V CHEMICAL METERING PUMPS - Manual (Page 15)

Page 14 Page 15
C3 C3
tm CHEM-PRO
C3V | Diaphragm Metering Pump
Made in the USA
MODE
PRIME
Program
Minimum
Maximum
Blue-White Ind. IP66
NEMA 4X
4 Enter the motor speed at the maximum mA input
signal value.
Press the DOWN button to select the digit to program.
The digit will blink when selected.
Press the UP button to change the selected digit.
Repeat until all digits are programmed.
Press the MODE button. The % SPEED icon will stop
blinking and the mA icon will blink indicating the
maximum mA value is ready to be programmed. The
currently programmed maximum value is shown on the
LCD.
MODE
6 8 10 12 14 18 20
0%
25%
50%
75%
100%
P
u
m
p
O
u
tp
u
t
M
o
to
r
S
p
e
e
d
Milliamp input (mA)
from external source
70%
Output
Mode 2 Programming Examples
4 Enter the maximum mA input signal value.
Note: this value must be greater than the minimum mA input signal value.
Press the DOWN button to select the digit to program. The digit will blink
when selected.
Press the UP button to change the selected digit.
Repeat until all digits are programmed.
Press the mode button. Programming is complete.
To exit the programming mode, press the MODE button for more than two
seconds. The PROGRAM arrow will disappear.
MODE
MODE
Example 1
4 mA will result in a pump output of
20.0%
16 mA will result in a pump output of
70.0%
4 16
Example 2
4 mA will result in a pump output of 0.0%
20 mA will result in a pump output of
100.0%
20%
Output
6 8 10 12 14 18
0%
25%
50%
75%
100%
P
u
m
p
O
u
tp
u
t
M
o
to
r
S
p
e
e
d
Milliamp input (mA)
from external source
100%
Output
4 16
0%
Output
20
tm CHEM-PRO
C3V | Diaphragm Metering Pump
Made in the USA
MODE
PRIME
Program
Minimum
Maximum
Blue-White Ind. IP66
NEMA 4X
Mode 2
4 Set the pump for mode 2.
Press the MODE button until MODE 2
is shown on the LCD display.
The %SPEED or mA icon will light
depending on the current display
setting.
The large LCD will indicate the current
motor speed or the current mA input
value.
4 Enter the programming mode.
While MODE 2 is displayed, press the
MODE button for more than two
seconds.
MODE
MODE
tm CHEM-PRO
C3V | Diaphragm Metering Pump
Made in the USA
MODE
PRIME
Program
Minimum
Maximum
Blue-White Ind. IP66
NEMA 4X
Blinking ARROW’s will point to the words PROGRAM
and MINIMUM indicating the program mode is
activated and the minimum value is ready to be
programmed. The % SPEED icon will blink indicating
the percentage of speed is ready to be programmed.
4 Enter the motor speed at the minimum mA input
signal value.
Press the DOWN button to select the digit to program.
The digit will blink when selected.
Press the UP button to change the selected digit.
Repeat until all digits are programmed.
Press the MODE button. The % SPEED icon will stop blinking and the mA
icon will blink indicating the minimum mA value is ready to be programmed.
The currently programmed minimum value is shown on the LCD.
4 Enter the minimum mA input signal value.
Note: this value must be less than the maximum mA input signal value.
Press the DOWN button to select the digit to program. The digit will blink
when selected.
Press the UP button to change the selected digit.
Repeat until all digits are programmed.
Press the MODE button. The mA icon will stop blinking and the % SPEED
icon will blink. The ARROW next to the word MAXIMUM will blink indicating
the maximum value is ready to be programmed. The currently programmed
maximum motor speed value is shown on the LCD.
MODE
MODE