Extron Electronics DMS 1600_2000_3200_3600 Setup Guide - Manual (Page 5)

DMS 1600, DMS 2000, DMS 3200, DMS 3600 • Introduction 2 3 DMS 1600, DMS 2000, DMS 3200, DMS 3600 • Introduction
About the DMS Matrix Switchers
The DMS 1600, DMS 2000, DMS 3200, and DMS 3600 (see figure 1)
are configurable matrix switchers that distribute DVI signals and DFX
transmitter and receiver outputs and inputs. I/O boards route signals
that are compatible with all Extron DVI video product lines and the
fiber optic outputs and inputs of DFX transmitters and receivers. The
matrix switcher routes any input signal to any combination of outputs.
The matrix switcher can route multiple input/output configurations
simultaneously.
AUDIO DVI-D INPUT
FOXBOX 4G Tx DVI
RS-232 OVER FIBER ALARM
Tx Rx 1 2
12V
1.0A MAX POWER
AUDIO DVI-D OUTPUT
FOXBOX 4G Rx DVI
RS-232 OVER FIBER ALARM
Tx Rx 1 2
12V
1.0A MAX POWER MODE
AUDIO DVI-D OUTPUT
FOXBOX 4G Rx DVI
RS-232 OVER FIBER ALARM
Tx Rx 1 2
12V
1.0A MAX POWER MODE
1
ON
2
AUDIO DVI-D INPUT
FOXBOX 4G Tx DVI
RS-232 OVER FIBER ALARM
Tx Rx 1 2
12V
1.0A MAX POWER MODE
1
ON
2
ANAHEIM, CA
RESET RS232/RS422
REMOTE LAN
ACT LINK
100-240V 50/60Hz 1.2A MAX.
100-240V 50/60Hz 1.2A MAX.
REDUNDANT
PRIMARY
DISCONNECT BOTH POWER
CORDS BEFORE SERVICING
1 - 4
5 - 8
9 - 12
13- 16
17 - 20
21 - 24
25 - 28
29- 32
33 - 36
FAN ASSEMBLY
FAN ASSEMBLY
PRIMARY POWER SUPPLY REDUNDANT POWER SUPPLY
DVI-D OUTPUTS A B C D
DVI-D OUTPUTS A B C D
DVI-D OUTPUTS A B C D
DVI-D OUTPUTS A B C D
DVI-D OUTPUTS A B C D
A B DVI-D INPUTS DVI-D OUTPUTS C D A B C D
A B DVI-D INPUTS DVI-D OUTPUTS C D A B C D
A B DVI-D INPUTS DVI-D OUTPUTS C D A B C D
A B DVI-D INPUTS DVI-D OUTPUTS C D A B C D
UPS 507
UNVERSAL SIGNAL PROCESSOR
ADJUST
DETAIL
ZOOM /PAN
BRIGHT /CONT
COLOR /TINT
SIZE
POSITION
MUTE
FREEZE
AUTO
IMAGE
PIP PRESET
6 7 5 4 3 2 1
MENU
NEXT
INPUTS
CONFIG
HD Camera
FOXBOX Tx DVI
FOXBOX Rx DVI
USP 507 PC
Extron
DMS 3600
Modular DVI Matrix Switcher
Digital Monitors
DVI Projectors
HDTV Monitors
Analog Monitor
DVI Equipped
PCs
Compact HDTV
Camera Systems
Figure 1. Typical DMS 3600 Application
Each matrix switcher model can be remotely controlled via its Ethernet
LAN port, a serial port, or a USB port using either the Windows-based
Extron Matrix Switchers Control Program or the SIS.
The switcher has two internal, hot-swappable 100 VAC to 240 VAC,
50-60 Hz, 175-watt power supplies that provide worldwide power
compatibility and reliability.
Configurability
The DMS matrix switchers are assembled from I/O boards.
• The DMS 1600 can include up to four I/O boards.
• The DMS 2000 can include up to five I/O boards.
• The DMS 3200 can include up to eight I/O boards.
• The DMS 3600 can include up to nine I/O boards.
There are six types of I/O boards available:
• 4x4 DVI inputs and outputs • 4x4 fiber inputs and outputs
• 4 DVI inputs • 4 fiber inputs
• 4 DVI outputs • 4 fiber outputs
By adding or removing I/O boards within certain rules that are detailed
in "Configurability rules," below, you can expand and contract each
switcher model from a 4-input by 4-output matrix to up to:
• DMS Matrix 1600 — A 16-input by 16-output matrix
• DMS Matrix 2000 — A 20-input by 20-output matrix
• DMS Matrix 3200 — A 32-input by 32-output matrix
• DMS Matrix 3600 — A 36-input by 36-output matrix
Configurability rules
There are certain rules for configuring the DMS matrix switcher for proper
operation, as detailed below:
• The top slot (slot 1) MUST contain a 4x4 DVI or fiber optic input and
output board.
• The next slot (slot 2) can contain any of the six board types.
• A 4x4 input and output board can be followed (in the slot directly
underneath it) by any of the board types.
• After you insert a 4-input board or a 4-output board, all active boards
underneath it MUST be the same size (4 inputs or 4 outputs).
• Fiber boards can follow DVI boards and DVI boards can follow fiber
boards within the above size rules.
• If you install a blank panel, all slots under it MUST contain blank
panels (you cannot skip a slot).